V-CP243NDN / NTN
V-CP243RDN / RTN
V-CP243NDG / RTS
E
S
S
N
D
English
Svenska
Suomen kieli
Norsk
Dansk
13
11
12
10
V-CP243NDN/NTN/NDG
16
13
14
15
V-CP243RDN/RTN/RTS
17
19
18
21
22
20
– 3 –
E
Using the cleaning head and Accessory
Information for your safety
Nozzles (depending on model)
Fit the large cleaning head onto the end of
the tube.
Please read all the following information,
which contains important instructions for the
safety, the use and the maintenance of the
appliance.
This appliance complies with the following EC
Directives: -73/23/EEC, 93/68/EEC-Low
Voltage Directive-89/336EEC -EMC Directive.
• The 2 position head(7) is equipped with a
pedal(8) which allows you to alter its
position according to the type of floor to be
cleaned.
Hard floor position(tiles, parquet
floors...). Press on the pedal to lower the
brush.
ꢀꢀNever allow children to use the appliance
unsupervised.
Carpet or rug position. Press on the
pedal to lift the brush up.
ꢀꢀDo not use the appliance If the supply
cord is damaged or faulty.
• Crevice Tool(9)
ꢀꢀIf the mains lead is damaged, it must be
replaced by an approved LG Electronics
Service Agent in order to avoid a hazard.
For vacuuming in those normally inaccess-
ible places i.e. reaching cobwebs, or down
the side of a sofa!
ꢀꢀAlways switch the vaccum cleaner off
before :
• changing the dust bag.
• Dusting brush(10)
For vacuuming picture frames furniture
outlines, books and other uneven objects.
• changing or cleaning the filters.
• Upholstery Nozzle(11)
ꢀꢀIf no dustbag is inserted, the cover cannot
be closed. Please do not use force!
For vacuuming uphostery, mattresses, etc.
The thread collectors help to pick up the
threads and fluff.
ꢀꢀDo not vacuum flammable or explosive
substances(liquids or gases).
How to plug in and use
Pull out the supply cord to the desired
length and plug into the socket.
ꢀꢀDo not vacuum hot ash, embers etc. nor
sharp objects.
ꢀꢀDo not vacuum water or other liquids.
Press button (13) to start the vacuum cleaner.
To stop it press the button (13) again.
How to Use
Adjusting the power level
• If your appliance is equipped with an
electronic variable power control(13), you
can choose the power appropriated for the
task. (depending on model)
Connecting the flexible hose
Push the end of the head(1) on the flexible
hose(2) into the attachment point on the
vacuum cleaner.
To remove the flexible hose from the
vacuum cleaner, press on the button(3)
situated on the head, then pull upwards.
•
The flexible hose handle(14) has a manual
air flow regulator(15) which allows you to
briefly reduce the suction level.
Storage(16)
Assembling the tubes
(depending on model)
• Metal or plastic tube(4)
- Fit together the two tubes by twisting
slightly.
When you have switched off and unplugged
the appliance, press on the button (12) to
automatically rewind the cord.
You can move or store your appliance in a
vertical position by sliding the hook on the
large cleaning head into the clip on the
underside of the appliance.
• Telescopic tube(5)
- Push spring latch(6) forward.
- Pull out tube to required length.
- Release spring latch to lock.
– 4 –
E
Changing the dust bag
What to do if your appliance
does not work?
The dustbag needs changing when the cleaner
is set to maximum power and the cleaner head
is off the floor but the “bag full” indicator
window(17) is completely coloured red.
Check that the appliance is correctly plugged
in and that the electrical socket is working.
Even if the dustbag does not appear to be
full at this stage, it should be changed.
It could be that a great deal of very fine dust
has clogged up the pores of the dust bag.
What to do when the suction
performance reduces?
• Turn off the appliance and unplug it.
• Open the cover by pressing the hook(18)
and lifting it up until it snaps into place.
• Stop the appliance and unplug it.
• Check that the tubes, flexible hose and
cleaning tool are not blocked.
Your appliance is equipped with either a
paper dust bag (19) or a fabric dust bag
(21)(depending on model).
• Check that the dust bag is not full.Replace
if necessary.
• Take hold of the dust bag by the handle
and pull.Remove the bag and throw it
away.
• To refit a new bag push the cardboard
support of a new bag into the bag mount
(20)until it will go no further.
If your appliance is fitted with a fab-
ric dust bag follow the same instructions
as above.
Empty it and replace it(21).
Note: as the appliance is fitted with a safety
device which checks that the bag is in place
you cannot close the lid if the bag is not
fitted correctly.
Cleaning the motor filter
The motor filter is situated inside the
appliance between the dust bag and the
motor. Each time that you change the air
outlet filter we advise you to remove the
motor filter(22)and to clean it by tapping to
remover the dirt and then replacing it in the
vacuum cleaner.
– 5 –
MEMO
– 14 –
MEMO
– 15 –
|