TROUBLE SHOOTING
Before going through the check list, check wiring connection.If any of the problems
persist after check list has been made, consult your nearest service dealer.
Symptom
No power.
Cause
Solution
If the power supply is properly
connected to the car accessory
terminal,switch the ignition key
The car ignition switch is
not on.
to " CC"
A
OWNER's MANUAL
The fuse is blown.
Replace the fuse.
Mobile Video System
Remove the disc in the player,
Then put a new one
Presence of disc inside the
player.
Disc cannot be
loaded or ejected.
Inserting the disc in reverse
direction.
Insert the compact disc with
the label facing upward.
The disc is extremely dirty or
defective.
Clean the disc or try to play a
new one.
Temperature inside the car
is too high.
Cool off or until the ambient
temperature return to normal.
Leave the player off for an hour
then try again.
Condensation.
Adjust volume to a desired level.
No sound.
Volume is in minimum.
Check wiring connection.
Wiring is not properly
connected.
Adjust the installation angle less
than 30 degrees.
Sound skips.
The installation angle is
more than 30 degrees.
The disc is extremely dirty
or defective disc.
Clean the compact disc, then
try to play a new one.
The operation keys
do not work.
Press the RESET button.
Front panel is not properly fixed
into its place.
The built-in microcomputer
is not operating properly
due to noise.
The radio does not
work.
The antenna cable is not
connected.
Insert the antenna cable firmly.
Select a station manually.
The signals are too weak.
ANTI-THEFT FLIP DOWN DETACHABLE PANEL
AUTO-LOADING COMPACT DISC PLAYER
AM/FM/LW(OPTIONAL)-STEREO DIGITAL PLL TUNING RADIO
WITH INFRARED REMOTE CONTROLLER
WWW.Legacycaraudio.com
11
NOTES
BASIC OPERATION
DISC PLAY:
Cleaning discs
Before playing, clean the disc with a clean, lint-free.
Flip the disc in the direction of the arrow.
NOTE:
.Do not use so solvents such as benzine, thinners. Commercially available
cleaners or anti static spray damage the unit.
Insert a disc with the label surface down. Doing so may damage the unit.
NOTE:
. Do not try to insert another disc when one has been already inserted.
Doing so may damage the unit.
Handle the disc by its edge. And to keep the disc clean, do not touch
the surface.
.Do not stick paper or tape on the disc.
.Do not expose the disc to direct sunlight or heat sources such as hot air
ducts. Or leave it in a car parked in direct sunlight where there can be a
considerable rise in temperature.
Label
surface up
Preparing the Remote Control
Inserting the Batteries
1.Open the battery compartment cover.
2.Insert the new batteries. Make sure that the positive and negative terminals of the
batteries are oriented indicated.
3.Close the cover
Using the Remote Control
Face the remote control towards the player front face IR mark (remote control signal
receiver).
Operation angle: About +30 degree in each the direction of the front of the IR mark.
9
2
BASIC OPERATION
1. OPEN BUTTON
INSTALLATION
Press it to flip down the front panel then you can insert the cd disc into the cd compartment
EJ button on the back of the front panel,press it to eject the disc.
2.8.9 SEL( AUDIO MODE SELECT)/ +/- BUTTONS
CAUTION: Do not install the detachable panel before connecting the wire.
1. The unit is designed for negative terminal of the battery which is connected
to the vehicle metal. Please confirm it before installation.
Press SEL button to change the mode in the sequence of
VOL
(Volume)
BAS
(Bass)
TRE
(Treble)
BAL
(Balance)
FAD
(Fader)
A.The volume level can be adjusted at any time by pressing the audio level+ or - button as
select mode has been initially defaulted at volume mode.
2. If the car interior is extremely hot, as after being parked in the sun, do not
use the player until the car has been driven for a while to cool off the interior.
The volume level is also obtained by stepping through the SEL button until the function
VOL is displayed and then press + or - button to adjust the sound level.
B.Press sel button to select the BAS,TRE ,BAL,FAD then press +/-button to adjust tthem.
C.Press SEL button hold for more than 2 seconds and select + or - button can have a beep sound.
3.10.TRACK UP /DOWN BUTTONS
3. Press the OPEN button to flip down the front panel (see fig.1), then take
away the front panel (see fig.2) and put it in the protective case (see fig.3)
safe keeping.
A. During CD mode, press
button allow you to track forwards.
4. Install the front panel back into its bracket and then push it back to the
position for playing (see fig.4).
Hold the
button allow you to skip forwards.
B. During Mp3 mode, press
button allow you to track forwards.
Hold the
button allow you to skip forwards.
For Mp3 playing(MP3 model only), these two buttons act as the digit 8 & 9 key.
C. During RADIO mode, press and hold
manual search channel.Then press
4.BAND BUTTON
or
for more than 2 seconds you can
, you can have auto search channel.
or
Press it to select your desired radio band and the band which is selected will be displayed
on LCD.
Press it hold for more than 2 seconds can have LOUD mode.
LOUD MODE:
When reduce the volume to half level, press it to enhance the bass effect.
For Mp3 playing(MP3 model only), this button can act as the ENTER key.
5.CLOCK BUTTON
Press it to display time on LCD for few seconds.Press it hold and then press
button to adjust hour or minute.
or
OPEN BUTTON
6.POWER BUTTON
Press it to turn on or off the unit.
7.AF BUTTON(for RDS model only)
AF [ALTERNATIVE FREQUENCIES](For RDS only)
( FIG.1)
( FIG.2)
When pressed short, AF switching mode is selected and the state of AF switching mode is
displayed by AF segment in display
Segment off: AF switching mode off.
Segment on: AF switching mode on, and has RDS information.
PROTECTIVE CASE
Segment flashing: AF switching mode is selected, but RDS information is not received yet.
When AF switching mode is selected, the radio checks the signal strength of AF all the time.
The interval of checking time of each AFs depends on the signal strength of current station,
from a few minute for strong station to a few seconds for weak station. Everytime that new
AF is stronger than current station, it switches over to that frequency for very short time, and
NEW FREQUENCY is displayed for 1-2 second. Because the mute time of AF switching or
checking time is very short, it is almost inaudible in case of normal program.
When pressed long, it is activated of regional mode on /off .
Regional mode ON
AF switching or PI SEEK is implemented to the station which have all PI codes are the
same as current station.
REG of individual segment is turned on also together with displaying REG ON numeric
3
8
INSTALLATION
BASIC OPERATION
display for a few seconds.
Regional mode OFF
The regional code in the format of PI code is ignored when AF switching or PI SEEK is
implemented.
DASH BOARD
REG of individual seg. is turned off together with displaying
REG OFF on numeric display for a few seconds.
11-12-13-14-15-16. PRESET MEMORY BUTTONS
A). To memorize the current frequency, press any one of the six preset Buttons hold for more
than 2 seconds.
B). To recall the preset memory, press one of the preset buttons [0-6].
C) RADIO MODE
METAL MOUNTING STRAP
HEX NUT
SPRING WASHER
CONSOLE
PLAIN WASHER
TAPPING SCREW
SLIDE BRACKET HOUSING
When pressed short, these keys select a preset station directly, When pressed longer than
one seconds,
HEX BOLT
current station is stored in preset memory bank. When PTY mode is selected, the preset
memory buttons is shared as follows:
PTY music group - - PTY speech group - - OFF MUSIC SPEECH
1. POP M, ROCK M
2. EASY M, LIGHT M
3. CLASSICS, OTHER M
4. JAZZ, COUNTRY
5. MATION M, OLDIES
6. FOLK M
1. NEWS, AFFAIRS, INFO
2. SPORT, EDUCATE, DRAMA
3. CULTURE, SCIENCE, VARIED
4. WEATHER, FINANCE, CHILDREN
5. SOCIAL, RELIGION, PHONEIN
6. TRAVEL, LEISURE, DOCUMENT
D). In CDP mode, press 1PAU button to pause CDP playing, press it again to resume CDP
playing.
E). In CDP mode, press 2SCN button to play the first 10 seconds part of each song, press it
again to stop scanning and retain playing the song currently selected.
F). In CDP mode, press 3RPT button to play the current track repeatedly. Press it again to
cancel this mode.
G). In CDP mode, press 4SHF button to play the track in random order. Press it again to
cancel this mode.
H).In CDC mode M5/M6: It moves to up or down the DISC, then play.
17.APS/MP3 BUTTON
While installing the front panel,
please mount the left side first,
then push the right side.
In radio mode:
When short pressing, the radio searches for each preset station.
When the field strength level is more than the threshold level of stop level, the radio is
holding at that preset number for few secretary with releasing mute, and than searches
again. In FM band, FM 1, FM 2 and FM 3 is checked one at a time. When long pressing (more
than 1 second),Zhe radio searches from the current frequency and checks the signal streng
th level until 1 cycle search is finished. And then 6 strongest stations are preset to the corres
ponding preset number. The AS operation is implemented in the each band of selected band.
When the AS operationis finished, the radio executes the preset scan.
In MP3 mode, press 0-9 and ENTER button to play the track in 1-108 number.
18.MODE BUTTON
TAPPING SCREW (M1.7X4 KM BLACK)
Press it repeatedly to select CDP, AUX and RADIO mode in sequence and circulation.
For SUB WOOFER function(optional), press and hold for more than 2 seconds can have
WOOFER Mode.
For Mp3 playing(MP3 model only), this button can act as the digit 7 key.
19.PTY(PROGRAM TYPE) BUTTON
This key is operated as follows:
PTY MUSIC group- - PTY SPEECH group- - PTY OFF
While selecting PTY TYPE, its selection is implemented by preset buttons as described in preset key.
7
4
BASIC OPERATION
ELECTRIC CONNECTION
When PTY is selected, the radio starts to search corresponding PTY information, and stops if the
FOR 4X40W
corresponding PTY information is detected.
If corresponding PTY information is not existed any more, PTY type is automatically exit to
normal mode.
20.TA BUTTON(for RDS model only)
AUX cable(optional)
ANTENNA CONNECTOR
RCH RED
LCH WHITE
TAfunction [TRAFFIC ANNOUNCEMENT] BUTTON(For RDS only)
When pressed short, it is activated as TA mode on or off.
OR
When TA mode is on and traffic announcement is transmitted:
1).When the unit is in CD mode, it will switch to radio mode temporarily.
2).Temporary switch over to an EON linked station when EON detects a traffic
announcement on that other program.
CDCcannector(optional)
IGNITION
SWITCH(B+)
RED
0.5A
FUSE BOX
YELLOW
FRONT RCA OUTPUT
CABLE(optional)
MEMORY(B+)
RCH RED
LCH WHITE
3).If the volume level was under the threshold point, it will be raised to the threshold point.
But the user changed the volume level which was more than the threshold point(min. TA
volume level),it will be set to the last level.
BLACK
BLUE
GROUND(B-)
AUTO
ANTENNA
FRONT
FRONT
When pressed long , it is selected EONTA LOCAL / EONTA DISTANCE mode.
The purpose of this key is to reduce unwanted EON TAswitching, which EON TA
information was received from current station and the radio switched to that EON
linked station, but no information could not be received because the EON linked
station is located too far from that area.
So the radio is switched back to current station again.
In above operation, a customer listen to a wrong program or mute sound for a while.
- EONTA LOCAL mode
WHITE
GREY
WHITE/BLACK
GREY/BLACK
Lch SPK
REAR
Rch SPK
REAR
GREEN
VIOLET
VIOLET/BLACK
GREEN/BLACK
Rch SPK
Lch SPK
When the filed strength level of EON linked is less than the threshold level, the radio
does not switch that station, and a customer can hardly listen to any disturbances.
When EONTA LOACL mode is selected, EONTA LO on numeric display is indicated
for a few seconds.
FOR WOOFER( 4X40W)
- EONTA DISTANCE mode
AUX cable(optional)
ANTENNA CONNECTOR
EON TA switching is try to implemented by the information of current station .
When EONTA DISTANCE mode is selected, EONTADX on numeric display is
indicated for a few seconds.
RCH RED
LCH WHITE
OR
SUB WOOFER
RCA
21.SCAN BUTTON
CDCcannector(optional)
IGNITION
SWITCH(B+)
GREEN
RED
0.5A
Press it to scan up by one channel step with station detection. If a valid signal has detected,
the current frequency is blinked with in 5 seconds, then press it again to stop scan and
remain the current frequency; otherwise, the unit continue to scan up by one channel step
with station detection 5 seconds later.
FUSE BOX
YELLOW
FRONT RCA OUTPUT
CABLE(optional)
MEMORY(B+)
RCH RED
LCH WHITE
BLACK
BLUE
GROUND(B-)
AUTO
ANTENNA
FRONT
22.DSP BUTTON
FRONT
Press it to switch between 4 preset equalizer curves:FLAT,CLAS,POP M,ROCK M,The
sound quality will be changed.
23.MUTE BUTTON
Press it to eliminate the sound immediately.
24.FLASHING LED
If the front panel is not on the main unit, LED will be flashing.
25.RESET
RESET button is placed on the housing and must be activated with either a
ballpoint pen or thin metal object. The RESET button is to be activated for the
following reasons:
WHITE
GREY
WHITE/BLACK
GREY/BLACK
Lch SPK
REAR
Rch SPK
REAR
GREEN
VIOLET
VIOLET/BLACK
GREEN/BLACK
Rch SPK
Lch SPK
-Initial installation of the unit when all wiring is completed.
-All the function buttons do not operate.
-Error symbol on the display.
Note: If press RESET button, the unit can't work yet, please use a cotton swab
soaked in isopropyl alcohol to clean the socket on the back of the front panel.
NOTE:
In spite of having any kinds of speaker system, must use 4 ohms
impedance of speaker to reduce the distortion during high volume
level.
5
6
|