®
PROGRAMMABLE
COMPACT DISC PLAYER
MODEL CD-50
OPERATING INSTRUCTIONS
PLAYS ALL MUSIC COMPACT DISCS
•
6 DIGIT LCD VISUAL DISPLAY
•
TRACK REPEAT & DISC REPEAT
•
DELUXE STEREO HEADPHONES INCLUDED
•
USES 4 SIZE “AA” BATTERIES (NOT INCLUDED)
•
PLEASE READ CAREFULLY BEFORE USE
CD-50(70A-0A9)121000 NL v.1
E
POWER SOURCES
Power your CD player by connecting an optional AC ADAPTOR or by inserting 4 size
“AA” fresh alkaline batteries.
NOTE: The only AC ADAPTOR suitable for this player is DC 4.5V 600mA, with polarity
, others may damage your player. Please check voltage + current (mA)
before buying an AC ADAPTOR.
Using with batteries
Insert 4 size AA alkaline batteries
according to the + and - markings on
the back cabinet near the BATTERY
COMPARTMENT DOOR.
Tips on battery use
Reversing polarities will damage the batteries and possibly your set. Be sure to
follow polarity ( + and - ) as indicated.
•
Do not mix different types together (Alkaline, Carbon-Zinc, Nickel-Cadmium etc.),
or old batteries with new ones.
•
When not in use for an extended period of time, or while internal batteries will not
be used, remove them to prevent possible acid leakage or corrosion resulting in
damage to your player.
•
When the batteries have become discharged, they must be disposed of in a safe
manner that complies with all applicable laws.
•
Installation of batteries should only be done by an adult (for safety).
•
Alkaline battery life
Bear in mind that battery life expectancy is based upon volume listening levels.
Maximum battery power consumption happens at maximum settings. Typical life
for 4 size “AA” alkaline batteries is about 16 hours of continuous use.
When
shows or flashes in the display
If the alkaline batteries are weak and discharged, this symbol “
” shows or
flashes in the display, then the power automatically turns off. If this occurs, replace
the alkaline batteries (also if display does not show anything, the batteries are
dead).
2
DISC PLAYING
1 Load the disc.
Push
here
Disc
Label side up
Press to open
2 Connect the headphones.
Stereo headphones
To PHONES
3 Press the PLAY/PAUSE button (
).
TRACK NUMBER
ELAPSED PLAYING
CURRENTLY
TIME OF THE
PLAYING
CURRENT TRACK
PLAY/PAUSE
Button
4 Adjust the volume.
MAXIMUM
MINIMUM
VOLUME CONTROL
3
Other operations
Operation
Display window shows
Press
To pause play
TRACK NUMBER
CURRENTLY
PLAYING
PLAYING TIME
FLASHES
To release pause
and resume play
TRACK NUMBER
CURRENTLY
PLAYING
PLAYING TIME
ADVANCES
To stop
or
To turn off the power
TOTAL TRACKS
TOTAL PLAYING
TIME
once (or repeatedly)
once (or repeatedly)
depressed and release when the
To skip to the next track(s)
To skip to the previous track(s)
Keep
desired music section of the disc is found.
To go ahead at high speed
(search)
If you press and hold the SKIP button (
)
•
while the last track is playing, and the end of the
track is reached, the music stops and the display
will show the next track number, then power will
shut off after 30 seconds.
To go back at high speed
(search)
Keep
depressed and release when the
desired music section of the disc is found.
Get into Stop Mode (for programming)
Press the PLAY/PAUSE button
, the set
begins to play, then press the STOP (POWER
OFF) button , the display will show six digits
similar to the example show here.
TOTAL TRACKS
TOTAL PLAYING
TIME
Auto power off function
The power turns off automatically 30 seconds after all tracks on the disc have been
played or after the STOP button is pressed to stop play.
4
REPEAT PLAY
SINGLE TRACK REPEAT
Plays one song over and over till you press STOP.
SKIP
REPEAT
x 1
During play, select the song you want to repeat with
either of the SKIP buttons (
or
), then press the
REPEAT button once, the symbol REPEAT 1 appears in
the display.
The song currently playing will repeat over and over,
until you press STOP.
REPEAT 1
To resume normal play, press the REPEAT button
another two times.
REPEAT
ALL TRACKS REPEAT
Repeats all songs in order, till you press STOP.
During play, press the REPEAT button twice, the symbol
REPEAT ALL will show in the display.
All songs will keep playing in sequence 1, 2, 3, etc. and
when finished, will start all over again until you press the
STOP button.
REPEAT ALL
To resume normal play, press the REPEAT button again.
REPEAT PROGRAMMED PLAY
REPEAT
PROGRAM
After you have programmed your own sequence (as
instructed on page 6), you may play the songs repeatedly
in your programmed sequence.
1. Follow the instructions on page 6 and press the PLAY
button to start programmed play. PGM (program) will
show in the display.
PGM
REPEAT ALL
2. During play, press the REPEAT button twice, the
symbol REPEAT ALL will show in the display.
The set will play the songs in the order you programmed, when finished, will start all
over again until you press the STOP button.
5
PROGRAMMING YOUR PLAYING SEQUENCE
PROGRAMMED PLAY
The tracks (songs) on the disc can be programmed (arranged in advance) to play in
any order you prefer (up to 21 tracks can be programmed).
•
Programming Example:
Program Number
etc.
etc.
1
3
4
1
7
1
2
5
3
8
6
4
5
2
8
1
Track Number (song number)
During CD play, the PROGRAM button functions the same as the REPEAT button.
The set must be in stop mode to program it.
During programming, the word PGM (program) flashes in the display. To program
•
•
songs to play in your preferred order, follow steps below:
1.Press the PROGRAM button once in 3.Press the PROGRAM button. Track 3 is
stop mode.
now programmed.
PROGRAM
PROGRAM
X 1
X 1
Program # 2 will now show in the
display, ready for your next selection of
The word PGM will show in the DISPLAY.
track.
PGM
PGM
4.Repeat steps 2 and 3 to program other
tracks till you finish (up to 21 selections).
Program number
5.After programming is finished, press
PLAY to begin programmed play.
2.Press the SKIP button (
select track number 3 (example). PGM
will flash in the display.
or
) to
shows in the display together with PGM
,
and music begins.
SKIP
NOTE:
- The player will stop automatically after
all programmed tracks have been
played.
- To quit programmed play, press STOP
button once. Then you may press PLAY
button to re-start normal play.
PGM
Your programming will be lost:
When the alkaline batteries are
exhausted or removed, or the optional
AC ADAPTOR is disconnected.
•
Track number
When the power is shut off.
•
6
MAINTENANCE
Handling Compact Discs
Cleaning the lens
Dirty, scratched or warped discs may
•
A dirty lens will cause sound skipping. If
the lens is very dirty, the player may not
work. We suggest using a special cleaning
disk (not included) available in most music
and Hi-Fi stores. However, if you do not
have one, you may use the instructions
below.
cause skipping or noise.
Handle the disc only by the edges. To
keep clean, do not touch its surface.
•
Discs should be stored in their cases
after use to avoid scratches.
•
Do not expose discs to direct sunlight,
•
Use a cotton swab very slightly dampened
with alcohol to clean the lens.
high humidity, high temperatures, or
dust, etc. Prolonged exposure to
extreme temperatures can warp the disc
(such as leaving the discs in your car
during summertime).
Cleaning the cabinet
Wipe with a soft cloth. If the cabinet is
very dirty, dampen (not dripping wet) the
cloth with a weak solution of soapy water,
and then wipe clean.
Do not stick or write anything on either
•
side of disc. Sharp writing instruments,
or the inks used in some felt-tip pens, may
damage its surface.
Cleaning the Discs
To remove the Disc
Fingerprints should be carefully wiped
Open the CD DOOR by pressing the
•
from the surface of disc with a soft cloth. DOOR OPEN button, hold the disc by the
Unlike conventional records, compact edge while slightly pressing on the center
discs have no grooves to collect dust spindle as illustrated, then lift it from the
and microscopic dirt, so gently wiping edge to release and remove.
them with a soft cloth should remove
most particles. Wipe in a straight
motion from the center to the edge.
NOTE
Always press STOP button and wait for
Never use thinner, benzine, record
•
the disc to stop rotating before pressing
cleaner or antistatic spray on a compact
the DOOR OPEN button to remove the
disc. Such chemicals can damage its
plastic surface.
disc.
7
SAFETY PRECAUTIONS
Do not take the set apart. The laser beam used in the set may harm your eyes. Refer
servicing to qualified service personnel only.
Do not insert pins or coins, clips, or any objects inside the set.
This set is equipped with a safety device which automatically turns the laser beam off
when the disc door is opened.
Do not drop the set or subject it to strong shocks. Doing so could result in damage.
Do not place the set in locations where the temperature is high, or in humid or dusty
locations, or locations with long heavy vibrations, or tilted surfaces.
The set’s cabinet may warp or the set may otherwise be damaged if it is placed in direct
sunlight, near heaters (where the temperature is 1400F/600C or higher) or in cars with
the windows closed.
In the summer, the temperature may get as high as 2120F /1000C or more.
Use the set within a temperature range of 410F/ 50C to 950F / 350C.
Use ONLY the DC 4.5V 600mA AC Adaptor with polarity
, others may damage
your set. Disconnect the Adaptor from the wall outlet when the set is not to be used for
an extended period of time (3 days or more).
When cleaning your set, use a soft dry cloth. Do not use solvents or commercially
available cleaners, as they may damage or discolor the finish.
Do not wear headphones while operating a motor vehicle. This could create a traffic
hazard and is illegal in many areas. Do not use this set when bicycling or running.
The headphones supplied with your set provide superb stereo listening while allowing
you to hear some outside sounds when listening at normally low volume levels. Listening
at extremely high volume levels minimizes the intrusion of outside noise/sounds. In the
interest of safety, it is strongly advised against the use while engaging in activities
where the exclusion of external sounds (whistles, horns, sirens, traffic, etc.) could be
hazardous. Also loud volume can hurt your ears. If you notice that the sound has
become weak or distorted or if tracks do not change, this is an indication that your
batteries are low. Replace both batteries at the same time (see BATTERY OPERATION).
Your CD-50 is identified by a serial number located in the Battery Compartment. Record
this number in the space provided below.
Model CD-50 Serial No.
Date Purchased:
This booklet contains detailed information on its safety and use. Please read it carefully
so that you may take full advantage of its many features, and ensure a safe reliable
operation. Keep this booklet for future reference.
CONDENSATION
If cold water is poured into a glass, water droplets form on the outside of the glass.
This is called condensation. Condensation may occur on internal operating parts of the
lens.
Condensation occurs:
When the set is brought from the cold outdoors into a warm room, or if it is in a cold
room to a room which is heated, or in the summer, if the set is moved from an air-
conditioned room or car to a hot or humid location.
Should condensation occur, the set may not operate properly. Open the CD Door and
wait for about 20 minutes (to allow the internal parts to adjust to the surrounding
temperature) before using the set.
8
IMPORTANT INFORMATION REQUIRED BY THE FCC
Since the CD circuitry may cause interference to other radios nearby, switch this
set off when not in use or move it away from the affected radios.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesirable operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
•
•
•
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
•
SAFETY CERTIFICATION
This Compact Disc Player is made and tested to meet safety standards of the FCC
requirements and compliance with safety performance of the U.S. Department of Health
and Human Services, and also with FDA Radiation Performance Standards 21 CFR
Subchapter J.
WARNING
To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
Unauthorized recording of copyrighted material may violate laws. Do not copy songs
without permission of the copyright holder.
•
•
LASER SAFETY
THIS SET EMPLOYS AN OPTICAL LASER BEAM SYSTEM IN THE CD MECHANISM,
DESIGNED WITH BUILT-IN SAFEGUARDS. DO NOT ATTEMPT TO DISASSEMBLE.
EXPOSURE TO THIS INVISIBLE LASER LIGHT BEAM MAY BE HARMFUL TO HUMAN
EYES. THIS IS A CLASS-1 LASER PRODUCT. USE OF ADJUSTMENTS OTHER THAN
THOSE SPECIFIED HEREIN, MAY RESULT IN HAZARDOUS LASER LIGHT BEAM
EXPOSURE. THIS COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR
REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE PERSONNEL. THE LASER
MECHANISM IN THE SET CORRESPONDS TO THE STYLUS (NEEDLE) OF A RECORD
PLAYER. ALTHOUGH THIS PRODUCT USES A LASER PICK-UP LENS, IT IS
COMPLETELY SAFE WHEN OPERATED ACCORDING TO DIRECTIONS.
9
TROUBLE SHOOTING GUIDE
Symptoms
Causes
Solutions
Replace all the 4 batteries with fresh
alkaline batteries. Battery life with
fresh batteries is about 16 hours
(rechargeable batteries have 1/2 of
that life).
Batteries are weak (they
may test OK on tester but
they are weak for CD
operation).
Tracks do not
change or set
does not play
normally.
Replace all the 4 batteries with fresh
ones.
Dead or weak batteries.
CD Player will not
turn on.
Check AC ADAPTOR (optional)
connection at AC outlet and the
back side of set.
AC ADAPTOR (optional)
not connected properly.
Re-insert disc with label side facing
up.
Disc inserted incorrectly.
Try another compact disc.
Close the door securely.
Defective compact disc.
CD DOOR not closed.
Disc will not play.
Take out the CD and leave the CD
Door open for about 20 minutes to
dry the moisture condensation.
Moisture has formed inside
the CD deck.
Headphone plug not
inserted properly.
Re-insert headphone plug into
PHONES jack.
No sound from
headphones.
Volume Control set to
minimum.
Increase the volume.
Replace with fresh batteries or use
an optional AC ADAPTOR.
Weak batteries.
Defective compact disc.
Try another compact disc.
The compact disc or lens Clean or replace the compact disc
is dirty or CD is scratched. or clean the lens.
Sound is skipping
or sound stops.
Place the CD player on a level
Strong vibrations.
surface that is stable.
Music is too loud.
Weak batteries.
Lower the VOLUME CONTROL.
Sound is distorted.
Replace all the 4 batteries or use an
optional AC ADAPTOR.
Remove batteries and ADAPTOR
(optional). Wait 15 seconds and re-
insert. Make sure batteries are fresh
or Adaptor (optional) has power.
Electronic or static error
caused circuitry to lock.
Buttons do not
work.
10
TECHNICAL SPECIFICATIONS
CD PLAYER SECTION
Frequency response ..............................
Wow and flutter ......................................
Sampling frequency ................................
D/A converter .........................................
Error correction method ..........................
Pickup ...................................................
20Hz - 20kHz +1 / -2dB
Below measurable limits
44.1kHz
1-bit
CIRC
Optical 3-beam semiconductor laser
(780 nm wavelength)
Laser diode material GaAIAs
Laser output less than 44.6µw
GENERAL
Maximum output (stereo headphones) .....
Power Supply
20mW + 20mW
AC Adaptor Input...................................
DC .........................................................
Set Dimensions (approximate)
120V/60Hz - 4.5V DC Output (not included)
6V: Using 4 size “AA” batteries
Width ................................................
Depth ...............................................
Height ..............................................
5 1/8"
5 1/2"
1"
Weight (approximate) .............................
9.5oz. (270g) (set only)
LIMITED WARRANTY
We warrant this product to be free from defects in material and workmanship under
normal use for a period of 90 days after purchase and we will repair it free of charge or
replace it at no charge, should it become defective under this warranty, providing you
submit proof of purchase (sales slip) with the set.
During the initial 90 day period after original purchase, we will service or exchange, at no
charge, the set that is returned to LENOXX ELECTRONICS CORP. (LENOXX will pay the
shipping back to you). After the initial 90 day period expires, and for a period of 12 months
from original purchase, we will repair the unit covering any part(s) that need to be replaced
at no charge, but will charge for the cost of labor, return postage paid by Lenoxx.
This warranty does not apply to any products which have been subject to misuse,
neglect or accident. This warranty does not cover broken headphones or cabinet.
UNDER NO CIRCUMSTANCES WILL LENOXX ELECTRONICS CORP. BE LIABLE FOR
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitations
or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state. The following charges apply to repairs beyond the
warranty period: $20.00. Be sure to pack carefully and return postage paid insured
together with your money order (personal checks will not be accepted) and sales receipt to:
LENOXX ELECTRONICS CORP. 2 GERMAK DRIVE, CARTERET N.J. 07008
For customer service
Dial 1-800-315-5885
(MONDAY - THURSDAY 9:00 AM - 5:00 PM, FRIDAY 9:00 AM - 1:00 PM EST)
or Visit Our Website: http://www.lenoxx.com
© 2001 LENOXX ELECTRONICS CORP.
2 GERMAK DRIVE
CARTERET, N.J. 07008
MADE & PRINTED IN CHINA
11
QUICK INSTRUCTIONS
POWERING UP
MODEL CD-50
Power your CD player by connecting an optional AC ADAPTOR or by inserting 4 size
“AA” fresh alkaline batteries.
NOTE: The only AC ADAPTOR suitable for this player is DC 4.5V 600mA, with polarity
, others may damage your player. Please check voltage + current (mA)
before buying an AC ADAPTOR.
BATTERY OPERATION
1. Open the BATTERY DOOR.
2. Insert 4 size “AA” fresh alkaline batteries as shown.
NOTE: Player will not work, and batteries will be
drained, if not inserted as shown on the back
cabinet near the BATTERY COMPARTMENT
DOOR.
4 SIZE “AA”
BATTERIES
3. Close the BATTERY DOOR.
NOTE: If the symbol “
” shows or flashes in the display,
your batteries are weak and need replacement.
PLUGGING IN
Plug the headphones into the PHONES JACK on the
left side of the player, and put on the headphones.
TO PHONES
JACK
VOLUME CONTROL
Adjust this VOLUME CONTROL to your preference.
GET INTO STOP MODE (For Programming)
Press the PLAY/PAUSE button
, the set begins to
play, then press the STOP (POWER OFF) button
,
the display will show six digits similar to the example
shown here.
TOTAL TRACKS
TOTAL PLAYING
TIME
1
CD-50(70A-0A9)QI121000 NL v.1
E
QUICK INSTRUCTIONS
BASIC FEATURES
PLAYING A DISC
You can play compact discs that have this logo:
1. Slide the OPEN button to open the CD DOOR.
2. Place a disc on the center post with the label facing up,
and then gently push down on the center of the disc
until it clicks in.
3. Close the CD DOOR, press the PLAY button, the set
starts playing.
PAUSE
Pressing PLAY/PAUSE button while a disc is playing will pause play (the playing time of
the current track will flash). Press PLAY/PAUSE again to continue play.
STOP or POWER OFF
Press the STOP button once to stop play, and the set will turn itself off automatically
after 30 seconds.
REPEAT
During play, press the REPEAT button once, “REPEAT 1” will show. That song currently
playing will play and repeat again and again till you press STOP.
To repeat all songs, press the REPEAT button twice. “REPEAT ALL” will show. All songs
will play and then repeat. Press the REPEAT button again to return to normal play.
NOTE: During play, the PROGRAM button functions the same as the REPEAT button.
SKIP (
or
)
During play, press and hold the SKIP buttons
or
while the disc is playing to
search backward or forward through a particular track (or song).
Press several times to skip to a later or earlier song, or to get back to the beginning of
the song.
PROGRAMMING
To arrange the songs to play in a special sequence (1, 5, 2, 3, etc.) you can program
the set to your taste.
During stop mode, press the PROGRAM button, then press either SKIP button (
or
) to select the track you want. Repeat pressing PROGRAM button and SKIP
button (
or ) till you finish programming, then press PLAY. The set will play the
songs in the order that you programmed.
FOR OTHER FEATURES INCLUDING DETAILED
PROGRAMMING INSTRUCTIONS, PLEASE READ THE
OPERATING INSTRUCTIONS BOOKLET.
2
|