Power Quality Systems
Liebert HiSwitch2
Digital Static Transfer Switch
Optional Color Touch-Screen Interface
Standard LED Panel
The controls of the HiSwitch2 are intuitive and simple. The
pop-up menus are easy to understand and provide a wealth
of operational and diagnostic information.
This optional color LCD monitor is divided into three segments.
In addition to a system mimic diagram, there is a Status/Alarm
panel and a section dedicated to operator instructions and
menus. You benefit from improved operator effectiveness,
reduced training time, and less chance of operator error.
In case you need simplified version of interface, the
Standard LED Panel is a good and economic solution for the
customer. It is possible to monitor the unit and alert when a
problem occurs by means of a series of LEDs and buttons.
Both optional and standard Panel solutions can be accessed
from a terminal, or a PC running terminal emulation soft-
ware, that is attached to the unit.
03
SYSTEM#1
SYSTEM#2
Liebert Experience: Greater Overall Value
Bypass
Mains
Bypass
Mains
The design of the HiSwitch2 reflects our decades of leader-
ship in critical power and environmental system architecture:
Normal
Mains
Normal
Mains
Normal
Mains
Normal
Mains
Conservative design margins and excellent overload
capacity. Can also be placed against a wall or partition.
UPS #1 UPS #6
UPS #1 UPS #6
Designed for maintainability, with all power-train
components removable and serviceable from the front,
without shutting down the connected load.
HiSync
Internal CANBUS protocol: high-bandwidth communica-
tion between system components via twisted-pair
cables. Options can be added as simple network nodes.
Full range of communications options to fit any
monitoring strategy for the Optional LED Panel.
HiSwitch2
#1
Critical Load
Critical Load
The Liebert Experience means a wider variety of power system
solutions from one source. Ask your Emerson Network Power
representative for information about Liebert range of Power
Quality Solutions.
HiSwitch2
#2
Dual Bus System Configuration
All components are thoughtfully
arranged for straight forward
installation and maintenance.
For units up to 600 amps, the
entire power and control module
can be removed as an assembly.
Note the separate compartment
for option modules, upper right,
for safe and convenient field access.
Technical Features [Liebert Hiswitch2]
Rating (A)
Dimensions (W x D x H)
Weight*(kg)
[mm]
100
250
400
600
800
1000
762 x 813 x 1956
762 x 813 x 1956
965 x 813 x 1956
965 x 813 x 1956
2134 x 813 x 1956
2134 x 813 x 1956
354
354
544
544
1134
1134
*Note: Actual Weights will vary depending on installed options.
Specifications
Operating Specifications
Rack-out control/power assembly on units up to 600A,
to allow maintenance, service, or full replacement
without disrupting the critical load
Voltage: 208, 220, 240, 380, 400, 415 VAC
(field selectable), +/- 10%
3-pole configurations
Frequency: 50 or 60 Hz (field selectable), +/- 5%
Top and bottom cable entry
Short-circuit Withstand Capability: 100kA at 208VAC,
from 65kA to 100kA at 480VAC (depending on the rating)
Dual-lug installation bus with pem nuts for
single-hand installation and "hot" torque service
Sense and transfer time: 5ms maximum
Overload Capability: 125% for 10 minutes,
150% for 2 minutes, 110% for 1 hour
Optional Features*
Full range of Open Comms™ hardware and software
Internal modem for dialing out alarms to phone or pager
Operating Temperature: 0 to 40° C
Color touch-screen LCD interface
eliminates mechanical pushbuttons
Standard Features
All components front accessible for installation
and service; no side or rear access required
Intuitive user interface with
drop-down menus and dialog boxes
Triple-redundant DSP digital logic
Dual-redundant power supplies
100% rated, fuseless design
Programmable output relays for custom
customer alarms and connections
Customizable input relays allow alarms from other
devices to be displayed on HiSwitch2 display
Flash memory enables firmware updates
while supporting critical load
CANBUS internal control wiring
*Compatible with LCD Panel only
While every precaution has been taken to ensure accuracy and completeness in this literature, Liebert Corporation assumes no responsibility, and disclaims all liability for damages resulting
from use of this information or for any errors or omissions. © 2004 Liebert Corporation. All rights reserved throughout the world. Specifications subject to change without notice.
All names referred to are trademarks or registered trademarks of their respective owners. ® Liebert and the Liebert logo are registered trademarks of the Liebert Corporation.
® Keeping Business in Business is a registered trademark of the Liebert Corporation. The Emerson logo is a trademark and service mark of Emerson Electric Co.
Liebert HIROSS UPS Sales Headquarters
Via Leonardo da Vinci,8
Liebert HIROSS Services Headquarters
Via Leonardo da Vinci,8
Emerson Network Power Ltd - UK
Fourth Avenue, Globe Park - Marlow
Buckinghamshire - SL71YG
35028 - Piove di Sacco (PD)
35028 - Piove di Sacco (PD)
tel. +39 049 9719111 fax +39 049 9719317
tel. +39 049 9719111 fax +39 049 9717053
tel. +44 1628 403200 fax +44 1628 403203
|