Makita Cordless Saw BLS820 User Manual

Cordless Compound  
Miter Saw  
Equipped with Electric Blade Brake  
216 mm (8-1/2”)  
MODEL BLS820  
001764  
I N S T R U C T I O N M A N U A L  
WARNING:  
For your personal safety, READ and UNDERSTAND before using.  
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
 
For Your Own Safety Read Instruction Manual  
Before Operating Tool  
Save it for future reference  
GENERAL SAFETY PRECAUTIONS  
USA005-1  
(For All TOOIS)  
1. KNOW YOUR POWER TOOL. Read the  
owner’s manual carefully. Learn the tool’s  
applications and limitations, as well as the  
specific potential hazards peculiar to it.  
10. WEAR PROPER APPAREL. Do not wear  
loose clothing, gloves, neckties, rings,  
bracelets, or other jewelry which may get  
caught in moving parts. Nonslip footwear  
is recommended. Wear protective hair  
covering to contain long hair.  
2. KEEP GUARDS IN PLACE and in working  
order.  
11. ALWAYS USE SAFETY GLASSES. Also  
use face or dust mask if cutting operation  
is dusty. Everyday eyeglasses only have  
impact resistant lenses, they are NOT  
safety glasses.  
3. REMOVE  
ADJUSTING  
KEYS  
AND  
WRENCHES. Form habit of checking to  
see that keys and adjusting wrenches are  
removed from tool before turning it on.  
4. KEEP WORK AREA CLEAN. Cluttered  
areas and benches invite accidents.  
12. SECURE WORK. Use clamps or a vise to  
hold work when practical. It’s safer than  
using your hand and it frees both hands  
to operate tool.  
5. DON’T USE IN DANGEROUS ENVIRON-  
MENT. Don’t use power tools in damp or  
wet locations, or expose them to rain.  
Keep work area well lighted. Don’t use  
tool in presence of flammable liquids or  
gases.  
13. DON’T OVERREACH. Keep proper footing  
and balance at all times.  
14. MAINTAIN TOOLS WITH CARE. Keep tools  
sharp and clean for best and safest perfor-  
mance. Follow instructions for lubricating  
and changing accessories.  
6. KEEP CHILDREN AWAY. All visitors  
should be kept safe distance from work  
area.  
15. DISCONNECT BATTERY FROM TOOL  
before servicing; when changing acces-  
sories such as blades, bits, cutters, and  
the like.  
7. MAKE WORKSHOP KID PROOF with pad-  
locks, master switches, or by removing  
starter keys.  
8. DON’T FORCE TOOL. It will do the job bet-  
ter and safer at the rate for which it was  
designed.  
16. REDUCE THE RISK OF UNINTENTIONAL  
STARTING. Make sure switch is in off  
position before inserting battery.  
9. USE RIGHT TOOL. Don’t force tool or  
attachment to do a job for which it was not  
designed.  
17. USE RECOMMENDED ACCESSORIES.  
Consult the owner’s manual for recom-  
mended accessories. The use of improper  
accessories may cause risk of injury to  
persons.  
3
 
18. NEVER STAND ON TOOL. Serious injury  
could occur if the tool is tipped or if the  
cutting tool is unintentionally contacted.  
affect its operation. A guard or other part  
that is damaged should be properly  
repaired or replaced.  
19. CHECK DAMAGED PARTS. Before further  
use of the tool, a guard or other part that  
is damaged should be carefully checked  
to determine that it will operate properly  
and perform its intended function - check  
for alignment of moving parts, binding of  
moving parts, breakage of parts, mount-  
ing, and any other conditions that may  
20. DIRECTION OF FEED. Feed work into a  
blade or cutter against the direction of  
rotation of the blade or cutter only.  
21. NEVER LEAVE TOOL RUNNING UNAT-  
TENDED. TURN POWER OFF. Don’t leave  
tool until it comes to a complete stop.  
ADDITIONAL SAFETY RULES  
USB034-2  
DO NOT let comfort or familiarity with product (gained from  
repeated use) replace strict adherence to miter saw safety  
rules. If you use this tool unsafely or incorrectly, you can suffer  
serious personal injury.  
1. Wear eye protection.  
8. Always secure all moving portions before  
carrying the tool.  
2. Keep hands out of path of saw blade.  
Avoid contact with any coasting blade. It  
can still cause severe injury.  
9. Be aware that this tool is always in an  
operating condition, because it does not  
have to be plugged into an electrical out-  
let.  
3. Do not operate saw without guards in  
place. Check blade guard for proper clos-  
ing before each use. Do not operate saw if  
blade guard does not move freely and  
close instantly. Never clamp or tie the  
blade guard into the open position.  
10. Do not use the tool in the presence of  
flammable liquids or gases.  
11. Check the blade carefully for cracks or  
damage  
before  
operation.  
Replace  
4. Do not perform any operation freehand.  
The workpiece must be secured firmly  
against the turn base and guide fence  
with a vise during all operations. Never  
use your hand to secure the workpiece.  
cracked or damaged blade immediately.  
Gum and wood pitch hardened on blades  
slows saw and increases potential for kick-  
back. Keep blade clean by first removing it  
from tool, then cleaning it with gum and pitch  
remover, hot water or kerosene. Never use  
gasoline to clean blade.  
5. Never reach around saw blade.  
6. Turn off tool and wait for saw blade to  
stop before moving workpiece or chang-  
ing settings.  
12. Use only flanges specified for this tool.  
13. Be careful not to damage the arbor,  
flanges (especially the installing surface)  
or bolt. Damage to these parts could  
result in blade breakage.  
7. Remove battery from tool before chang-  
ing blade or servicing.  
4
 
14. Make sure that the turn base is properly  
secured so it will not move during opera-  
tion. Use the holes in the base to fasten  
the saw to a stable work platform or  
bench. NEVER use tool where operator  
positioning would be awkward.  
24. Do not attempt to lock the trigger in the on  
position.  
25. Be alert at all times, especially during  
repetitive, monotonous operations. Do  
not be lulled into a false sense of security.  
Blades are extremely unforgiving.  
15. For your safety, remove the chips, small  
pieces, etc. from the table top before oper-  
ation.  
26. Always use accessories recommended in  
this manual. Use of improper accessories  
such as abrasive wheels may cause an  
injury.  
16. Avoid cutting nails. Inspect for and  
remove all nails from the workpiece  
before operation.  
27. NEVER hold workpiece on right side of  
blade with left hand or vice versa. This is  
called cross-armed cutting and exposes  
user to risk of SERIOUS PERSONAL  
INJURY as shown in the figure. ALWAYS  
use vise to secure workpiece.  
17. Make sure the shaft lock is released  
before the switch is turned on.  
18. Be sure that the blade does not contact  
the turn base in the lowest position.  
19. Hold the handle firmly. Be aware that the  
saw moves up or down slightly during  
start-up and stopping.  
20. Make sure the blade is not contacting the  
workpiece before the switch is turned on.  
21. Before using the tool on an actual work-  
piece, let it run for a while. Watch for  
vibration or wobbling that could indicate  
poor installation or a poorly balanced  
blade.  
28. NEVER stack workpieces on the table top  
to speed cutting operations. Cut only one  
piece at a time.  
22. Wait until the blade attains full speed  
before cutting.  
29. Some material contains chemicals which  
may be toxic. Take caution to prevent dust  
inhalation and skin contact. Follow mate-  
rial supplier safety data.  
23. Stop operation immediately if you notice  
anything abnormal.  
SAVE THESE INSTRUCTIONS  
WARNING:  
MISUSE or failure to follow the safety rules stated in this  
instruction manual may cause serious personal injury.  
5
 
IMPORTANT SAFETY INSTRUCTIONS FOR  
CHARGER & BATTERY CARTRIDGE  
USC002-3  
1. SAVE THESE INSTRUCTIONS- This man-  
ual contains important safety and operat-  
ing instructions for battery charger.  
6. To reduce risk of damage to electric plug  
and cord, pull by plug rather than cord  
when disconnecting charger.  
2. Before using battery charger, read all  
instructions and cautionary markings on  
(1) battery charger, (2) battery, and (3)  
product using battery.  
7. Make sure cord is located so that it will  
not be stepped on, tripped over, or other-  
wise subjected to damage or stress.  
8. An extension cord should not be used  
unless absolutely necessary. Use of  
improper extension cord could result in a  
risk of fire and electric shock. If extension  
cord must be used, make sure:  
3. CAUTION - To reduce risk of injury, charge  
only MAKITA rechargeable batteries  
marked on the charger label. Other types  
of batteries may burst causing personal  
injury and damage.  
a. That pins on plug of extension cord  
are the same number, size, and shape  
as those of plug on charger;  
4. Do not expose charger to rain or snow.  
5. Use of an attachment not recommended  
or sold by the battery charger manufac-  
turer may result in a risk of fire, electric  
shock, or injury to persons.  
b. That extension cord is properly wired  
and in good electrical condition; and  
c. That wire size is at least as large as  
the one specified in the table below.  
Table 1: RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS FOR BATTERY CHARGERS  
Length of Cord (Feet)  
AWG Size of Cord  
25  
18  
50  
18  
100  
18  
150  
16  
9. Do not operate charger with damaged  
cord or plug - replace them immediately.  
13. The battery charger is not intended for  
use by young children or infirm persons  
without supervision.  
10. Do not operate charger if it has received a  
sharp blow, been dropped, or otherwise  
damaged in any way; take it to a qualified  
serviceman.  
14. Young children should be supervised to  
ensure that they do not play with the bat-  
tery charger.  
11. Do not disassemble charger or battery  
cartridge; take it to a qualified serviceman  
when service or repair is required. Incor-  
rect reassembly may result in a risk of  
electric shock or fire.  
15. If operating time has become excessively  
shorter, stop operating immediately. It  
may result in a risk of overheating, possi-  
ble burns and even an explosion.  
16. If electrolyte gets into your eyes, rinse  
them out with clear water and seek medi-  
cal attention right away. It may result in  
loss of your eyesight.  
12. To reduce risk of electric shock, unplug  
charger from outlet before attempting any  
maintenance or cleaning. Turning off con-  
trols will not reduce this risk.  
6
 
ADDITIONAL SAFETY RULES FOR CHARGER &  
BATTERY CARTRIDGE  
1. Do not charge Battery Cartridge when  
temperature is BELOW 10°C (50°F) or  
ABOVE 40°C (104°F).  
A battery short can cause a large current  
flow, overheating, possible burns and  
even a breakdown.  
2. Do not attempt to use a step-up trans-  
former, an engine generator or DC power  
receptacle.  
5. Do not store the tool and Battery Car-  
tridge in locations where the temperature  
may reach or exceed 50°C (122°F).  
3. Do not allow anything to cover or clog the  
charger vents.  
6. Do not incinerate the Battery Cartridge  
even if it is severely damaged or is com-  
pletely worn out. The battery cartridge can  
explode in a fire.  
4. Do not short the battery cartridge:  
(1) Do not touch the terminals with any  
conductive material.  
7. Be careful not to drop, shake or strike bat-  
tery.  
(2) Avoid storing battery cartridge in a  
container with other metal objects  
such as nails, coins, etc.  
8. Do not charge inside a box or container of  
any kind. The battery must be placed in a  
well ventilated area during charging.  
(3) Do not expose battery cartridge to  
water or rain.  
SAVE THESE INSTRUCTIONS  
SYMBOLS  
The following show the symbols used for the charger. Be sure that you understand their  
meaning before use.  
.......... Ready to charge  
.............Charging  
...........Delay charge (Cooling)  
........Defective battery  
....Conditioning  
.............Charging complete  
...........Cooling abnormality  
7
 
INSTALLATION  
001823  
Installing auxiliary plate  
1
Installing the auxiliary plate using the notch in the tools base  
and secure it by tightening the hex bolt.  
2
3
1. Base  
2. Hex bolt  
3. Auxiliary plate  
001832  
1
2
3
4
1. Auxiliary plate  
2. Base  
3. Hex bolt  
4. Nut  
Bench mounting  
001847  
When the tool is shipped, the handle is locked in the lowered  
position by the stopper pin. Release the stopper pin by lower-  
ing the handle slightly and pulling the stopper pin.  
1
1. Stopper pin  
001857  
This tool should be bolted with two bolts to a level and stable  
surface using the bolt holes provided in the tools base. This  
will help prevent tipping and possible injury.  
1
1. Bolt  
8
 
FUNCTIONAL  
DESCRIPTION  
CAUTION:  
Always be sure that the tool is switched off and the  
battery cartridge is removed before adjusting or  
checking function on the tool.  
001803  
Installing or removing battery cartridge  
31  
Always switch off the tool before insertion or removal of  
the battery cartridge.  
2
To remove the battery cartridge, withdraw it from the tool  
while sliding the button on the side of the cartridge.  
To insert the battery cartridge, align the tongue on the  
battery cartridge with the groove in the housing and slip  
it into place. Always insert it all the way until it locks in  
place with a little click. If you can see the red part on the  
upper side of the button, it is not locked completely.  
Insert it fully until the red part cannot be seen. If not, it  
may accidentally fall out of the tool, causing injury to you  
or someone around you.  
1. Button  
2. Battery cartridge  
3. Red part  
Do not use force when inserting the battery cartridge. If  
the cartridge does not slide in easily, it is not being  
inserted correctly.  
001336  
Charging  
2
1. Plug the battery charger into the proper AC voltage  
source. Two charging lights will flash in green color  
repeatedly.  
1
3
2. Insert the battery cartridge into charger until it stops  
adjusting to the guide of charger. Terminal cover of  
charger can be opened with inserting and closed with  
pulling out the battery cartridge.  
4
1. Terminal cover  
2. Battery cartridge  
3. Charging light  
4. Battery charger  
3. When the battery cartridge is inserted, the charging light  
color will change from green to red and charging will  
begin. The charging light will keep lighting up lit steadily  
during charging. One red charging light indicates  
charged condition in 0 - 80% and two red ones indicates  
80 - 100%.  
4. With finish of charge, the charging lights will change  
from two red ones to two green ones.  
9
 
5. If you leave the battery cartridge in the charger after the  
charging cycle is complete, the charger will switch into  
its trickle charge (maintenance charge)mode which  
will last approximately 24 hours.  
6. After charging, unplug the charger from the power  
source.  
NOTE:  
The battery charger is for charging Makita battery  
cartridge. Never use it for other purposes or for other  
manufacturers batteries.  
When you charge a new battery cartridge or a battery  
cartridge which has not been used for a long period of  
time, it may not accept a full charge. This is a normal  
condition and does not indicate a problem. You can  
recharge the battery cartridge fully after discharging it  
completely and recharging a couple of times.  
If you charge a battery cartridge from a just operated tool  
or battery cartridge which has been left in a location  
exposed to direct sunlight for a long time, the charging  
light may flash in red color. If this occurs, wait for a while.  
Charging will begin after the battery cartridge is cooled  
by the cooling fan installed in the charger. (DC24SA  
only) When the temperature on battery is more than  
approx. 70°C, two charging lights may flash in red color,  
and when approx. 50°C - 70°C, one charging light in red  
color.  
If the charging light flashes alternately in green and red  
color, charging is not possible. The terminals on the  
charger or battery cartridge are clogged with dust or the  
battery cartridge is worn out or damaged.  
Cooling system (DC24SA only)  
This charger is equipped with cooling fan for heated  
battery in order to enable the battery to prove its own  
performance. Sound of cooling air comes out during  
cooling, which means no trouble on the charger.  
Yellow light will flash for warning in the following cases.  
- Trouble on cooling fan  
- Incomplete cool down of battery, such as, being  
clogged with dust  
The battery can be charged in spite of the yellow  
warning light. But the charging time will be longer than  
usual in this case.  
10  
 
Check the sound of cooling fan, vent on the charger and  
battery, which can be sometime clogged with dust.  
The cooling system is in order although no sound of  
cooling fan comes out, if the yellow warning light will not  
flash.  
Always keep clean the vent on charger and battery for  
cooling.  
The products should be sent to repair or maintenance, if  
the yellow warning light will frequently flash.  
Conditioning charge (DC24SA only)  
Conditioning charge can extend the life of battery by auto-  
matically searching the optimum charging condition for the  
batteries in every situations.  
The battery employed in the following conditions repeatedly,  
will be worn out shortly, and yellow warning light may flash.  
1. Recharge of battery with its high temperature  
2. Recharge of battery with its low temperature  
3. Recharge of full charged battery  
4. Over-discharge of battery (continue to discharge battery  
in spite of down of power.)  
The charging time of such battery is longer than usual.  
Trickle charge (Maintenance charge)  
If you leave the battery cartridge in the charger to prevent  
spontaneous discharging after full charge, the charger will  
switch into its trickle charge (maintenance charge)mode  
and keep the battery cartridge fresh and fully charged.  
Tips for maintaining maximum battery life  
1. Charge the battery cartridge before completely dis-  
charged.  
Always stop tool operation and charge the battery car-  
tridge when you notice less tool power.  
2. Never recharge a fully charged battery cartridge.  
Overcharging shortens the battery service life.  
3. Charge the battery cartridge with room temperature at  
10°C - 40°C (50°F - 104°F).  
Let a hot battery cartridge cool down before charging it.  
4. Charge the Nickel Metal Hydride battery cartridge when  
you do not use it for more than six months.  
11  
 
001795  
Blade guard  
When lowering the handle, the blade guard rises automati-  
cally. The guard is spring loaded so it returns to its original  
position when the cut is completed and the handle is raised.  
NEVER DEFEAT OR REMOVE THE BLADE GUARD OR  
THE SPRING WHICH ATTACHES TO THE GUARD.  
1
In the interest of your personal safety, always maintain the  
blade guard in good condition. Any irregular operation of the  
blade guard should be corrected immediately. Check to  
assure spring loaded return action of guard. NEVER USE  
THE TOOL IF THE BLADE GUARD OR SPRING ARE DAM-  
AGED, FAULTY OR REMOVED. DOING SO IS HIGHLY  
DANGEROUS AND CAN CAUSE SERIOUS PERSONAL  
INJURY.  
1. Blade guard  
If the see-through blade guard becomes dirty, or sawdust  
adheres to it in such a way that the blade is no longer easily  
visible, remove the battery cartridge and clean the guard  
carefully with a damp cloth. Do not use solvents or any petro-  
leum-based cleaners on the plastic guard.  
001782  
If the blade guard is especially dirty and vision through the  
guard is impaired, use the supplied socket wrench to loosen  
the hex bolt holding the center cover. Loosen the hex bolt by  
turning it counterclockwise and raise the blade guard and  
center cover. With the blade guard so positioned, cleaning  
can be more completely and efficiently accomplished. When  
cleaning is complete, reverse procedure above and secure  
bolt. Do not remove spring holding blade guard. If guard  
becomes discolored through age or UV light exposure, con-  
tact a Makita service center for a new guard. DO NOT  
DEFEAT OR REMOVE GUARD.  
1
1. Blade guard  
12  
 
001799  
Positioning kerf board  
This tool is provided with the kerf boards in the turn base to  
minimize tearing on the exit side of a cut. The kerf boards are  
factory adjusted so that the saw blade does not contact the  
kerf boards. Before use, adjust the kerf boards as follows:  
First, remove the battery cartridge. Loosen all the screws  
(2 each on left and right) securing the kerf boards. Re-tighten  
them only to the extent that the kerf boards can still be easily  
moved by hand. Lower the handle fully and push in the stop-  
per pin to lock the handle in the lowered position. Adjust the  
kerf boards so that the kerf boards just contact the sides of  
the blade teeth. Tighten all the screws (do not tighten firmly).  
After adjusting the kerf boards, release the stopper pin and  
raise the handle. Then tighten all the screws securely.  
1
1. Kerf board  
001800  
1
2
3
CAUTION:  
4
5
Before and after changing the bevel angle, always adjust  
the kerf boards as described above.  
1. Saw blade  
2. Blade teeth  
3. Kerf board  
4. Left bevel cut  
5. Straight cut  
001801  
Maintaining maximum cutting capacity  
1
This tool is factory adjusted to provide the maximum cutting  
capacity for a 216 mm (8-1/2) saw blade.  
When installing a new blade, always check the lower limit  
position of the blade and if necessary, adjust it as follows:  
First, remove the battery cartridge. Lower the handle com-  
pletely. Use the socket wrench to turn the adjusting bolt until  
the periphery of the blade extends slightly below the top sur-  
face of the turn base at the point where the front face of the  
guide fence meets the top surface of the turn base.  
1. Adjusting bolt  
001540  
2
1
With the battery cartridge removed, rotate the blade by hand  
while holding the handle all the way down to be sure that the  
blade does not contact any part of the lower base. Re-adjust  
slightly, if necessary.  
3
CAUTION:  
1. Top surface ot turn base  
2. Periphery of blade  
3. Guide fence  
After installing a new blade, always be sure that the  
blade does not contact any part of the lower base when  
the handle is lowered completely. Always do this with the  
battery cartridge removed.  
13  
 
001802  
Adjusting the miter angle  
1
2
3
Loosen the grip by turning counterclockwise. Turn the turn  
base while pressing down the lock lever. When you have  
moved the grip to the position where the pointer points to the  
desired angle on the miter scale, securely tighten the grip  
clockwise.  
5
4
CAUTION:  
1. Miter scale  
2. Turn base  
3. Lock lever  
4. Pointer  
When turning the turn base, be sure to raise the handle  
fully.  
After changing the miter angle, always secure the turn  
base by tightening the grip firmly.  
5. Grip  
001804  
Adjusting the bevel angle  
To adjust the bevel angle, loosen the lever at the rear of the  
tool counterclockwise.  
Push the handle to the left to tilt the saw blade until the  
pointer points to the desired angle on the bevel scale. Then  
tighten the lever clockwise firmly to secure the arm.  
1
CAUTION:  
1. Lever  
When tilting the saw blade, be sure to raise the handle  
fully.  
001805  
After changing the bevel angle, always secure the arm  
by tightening the lever clockwise.  
1
2
When changing bevel angles, be sure to position the kerf  
boards appropriately as explained in the Positioning kerf  
boardssection.  
3
1. Arm  
2. Bevel scale  
3. Pointer  
001811  
Switch action  
CAUTION:  
1
2
Before inserting the battery cartridge into the tool,  
always check to see that the switch trigger actuates  
properly and returns to the OFFposition when  
released.  
When not using the tool, remove the lock-off button and  
store it in a secure place. This prevents unauthorized  
operation.  
1. Lock-off button  
2. Switch trigger  
14  
 
Do not pull the switch trigger hard without pressing in the  
lock-off button. This can cause switch breakage.  
To prevent the switch trigger from being accidentally pulled, a  
lock-off button is provided. To start the tool, press in the lock-  
off button and pull the switch trigger. Release the switch trig-  
ger to stop.  
WARNING:  
NEVER use tool without a fully operative switch trigger.  
Any tool with an inoperative switch is HIGHLY  
DANGEROUS and must be repaired before further  
usage.  
For your safety, this tool is equipped with a lock-off  
button which prevents the tool from unintended starting.  
NEVER use the tool if it runs when you simply pull the  
switch trigger without pressing the lock-off button.  
Return tool to a Makita service center for proper repairs  
BEFORE further usage.  
NEVER tape down or defeat purpose and function of  
lock-off button.  
Electric brake  
This tool is equipped with an electric blade brake. If the tool  
consistently fails to quickly stop blade after switch trigger  
release, have tool serviced at a Makita service center.  
The blade brake system is not a substitute for blade guard.  
NEVER USE TOOL WITHOUT A FUNCTIONING BLADE  
GUARD. SERIOUS PERSONAL INJURY CAN RESULT.  
ASSEMBLY  
CAUTION:  
Always be sure that the tool is switched off and the  
battery cartridge is removed before carrying out any  
work on the tool.  
15  
 
001840  
Socket wrench storage  
1
The socket wrench is stored as shown in the figure. When  
using the socket wrench, pull it out of the wrench holder.  
After using the socket wrench, return it to the wrench holder.  
2
1. Blade case  
2. Wrench holder  
Installing or removing saw blade  
CAUTION:  
Always be sure that the tool is switched off and the  
battery cartridge is removed before installing or  
removing the blade.  
Use only the Makita socket wrench provided to install or  
remove the blade. Failure to do so may result in  
overtightening or insufficient tightening of the hex bolt.  
This could cause an injury.  
001847  
Lock the handle in the raised position by pushing in the stop-  
per pin.  
1
1. Stopper pin  
001863  
To remove the blade, use the socket wrench to loosen the  
hex bolt holding the center cover by turning it counterclock-  
wise. Raise the blade guard and center cover.  
1
2
3
4
1. Center cover  
2. Socket wrench  
3. Hex bolt  
4. Blade guard  
16  
 
001765  
Press the shaft lock to lock the spindle and use the socket  
wrench to loosen the hex bolt clockwise. Then remove the  
hex bolt, outer flange and blade.  
1
2
3
1. Shaft lock  
2. Socket wrench  
3. Hex bolt  
001771  
To install the blade, mount it carefully onto the spindle, mak-  
ing sure that the direction of the arrow on the surface of the  
blade matches the direction of the arrow on the blade case.  
Install the outer flange and hex bolt, and then use the socket  
wrench to tighten the hex bolt (left-handed) securely counter-  
clockwise while pressing the shaft lock.  
2
3
1
4
5
Return the blade guard and center cover to its original posi-  
tion. Then tighten the hex bolt clockwise to secure the center  
cover. Release the handle from the raised position by pulling  
the stopper pin. Lower the handle to make sure that the  
blade guard moves properly. Make sure shaft lock has  
released spindle before making cut.  
1. Outer flange  
2. Inner flange  
3. Spindle  
4. Saw blade  
5. Hex bolt  
001783  
2
1
4
3
1. Arrow  
2. Blade case  
3. Saw blade  
4. Arrow  
17  
 
001798  
Dust bag  
The use of the dust bag makes cutting operations clean and  
dust collection easy. To attach the dust bag, fit it onto the  
dust nozzle.  
1
2
When the dust bag is about half full, remove the dust bag  
from the tool and pull the fastener out. Empty the dust bag of  
its contents, tapping it lightly so as to remove particles adher-  
ing to the insides which might hamper further collection.  
3
1. Dust nozzle  
2. Dust bag  
3. Fastener  
NOTE:  
If you connect a Makita vacuum cleaner to your saw, more  
efficient and cleaner operations can be performed.  
Securing workpiece  
WARNING:  
It is extremely important to always secure the workpiece  
properly and tightly with the vise. Failure to do so can  
cause the tool to be damaged and/or the workpiece to  
be destroyed. PERSONAL INJURY MAY ALSO  
RESULT. Also, after a cutting operation, DO NOT raise  
the blade until the blade has come to a complete stop.  
001549  
CAUTION:  
1
2
When cutting long workpieces, use supports that are as  
high as the top surface level of the turn base. Do not rely  
solely on the vertical vise and/or horizontal vise to  
secure the workpiece.  
Thin material tends to sag. Support workpiece over its  
entire length to avoid blade pinch and possible  
KICKBACK.  
1. Support  
2. Turn base  
18  
 
001806  
Vertical vise  
6
7
1
2
3
The vertical vise can be installed in two positions on either  
the left or right side of the guide fence or the holder assembly  
(optional accessory). Insert the vise rod into the hole in the  
guide fence or the holder assembly and tighten the screw to  
secure the vise rod.  
4
5
Position the vise arm according to the thickness and shape  
of the workpiece and secure the vise arm by tightening the  
screw. If the screw to secure the vise arm contacts the guide  
fence, install the screw on the opposite side of vise arm.  
Make sure that no part of the tool contacts the vise when  
lowering the handle all the way. If some part contacts the  
vise, re-position the vise.  
1. Vise arm  
2. Vise rod  
3. Guide fence  
4. Holder  
5. Holder assembly  
6. Vise knob  
7. Screw  
Press the workpiece flat against the guide fence and the turn  
base. Position the workpiece at the desired cutting position  
and secure it firmly by tightening the vise knob.  
CAUTION:  
The workpiece must be secured firmly against the turn  
base and guide fence with the vise during all operations.  
001807  
Horizontal vise (optional accessory)  
3
2
1
The horizontal vise can be installed on either the left or right  
side of the base. When performing 15° or greater miter cuts,  
install the horizontal vise on the side opposite the direction in  
which the turn base is to be turned. By turning the vise knob  
counterclockwise, the screw is released and the vise shaft  
can be moved rapidly in and out. By turning the vise knob  
clockwise, the screw remains secured. To grip the workpiece,  
turn the vise knob gently clockwise until the projection  
reaches its topmost position, then fasten securely. If the vise  
knob is forced in or pulled out while being turned clockwise,  
the projection may stop at an angle. In this case, turn the  
vise knob back counterclockwise until the screw is released,  
before turning again gently clockwise.  
4
1. Vise knob  
2. Projection  
3. Vise shaft  
4. Base  
The maximum width of the workpiece which can be secured  
by the horizontal vise is 120 mm (4-3/4).  
19  
 
CAUTION:  
Grip the workpiece only when the projection is at the  
topmost position. Failure to do so may result in  
insufficient securing of the workpiece. This could cause  
the workpiece to be thrown, cause damage to the blade  
or cause the loss of control, which can result in  
PERSONAL INJURY.  
002247  
Holders and holder assembly  
(optional accessories)  
The holders and the holder assembly can be installed on  
either side as a convenient means of supporting workpieces  
horizontally. Install them as shown in the figure. Then tighten  
the screws firmly to secure the holders and the holder  
assembly.  
1
2
1. Holder  
2. Holder assembly  
002246  
When cutting long workpieces, use the holder-rod assembly  
(optional accessory). It consists of two holder assemblies  
and two rods 12.  
2
CAUTION:  
Always support long workpieces level with the top  
surface of the turn base for accurate cuts and to prevent  
dangerous loss of control of the tool.  
1
1. Holder assembly  
2. Rod 12  
OPERATION  
CAUTION:  
Before use, be sure to release the handle from the  
lowered position by pulling the stopper pin.  
Make sure the blade is not contacting the workpiece, etc.  
before the switch is turned on.  
Do not apply excessive pressure on the handle when  
cutting. Too much force may result in overload of the  
motor and/or decreased cutting efficiency. Push down  
handle with only as much force as is necessary for  
smooth cutting and without significant decrease in blade  
speed.  
20  
 
Gently press down the handle to perform the cut. If the  
handle is pressed down with force or if lateral force is  
applied, the blade will vibrate and leave a mark (saw  
mark) in the workpiece and the precision of the cut will  
be impaired.  
001812  
1. Press cutting  
Secure the workpiece with the vise. Switch on the tool  
without the blade making any contact and wait until the  
blade attains full speed before lowering. Then gently  
lower the handle to the fully lowered position to cut the  
workpiece. When the cut is completed, switch off the tool  
and WAIT UNTIL THE BLADE HAS COME TO A COM-  
PLETE STOP before returning the blade to its fully ele-  
vated position.  
2. Miter cutting  
Refer to the previously covered Adjusting the miter  
angle.  
001813  
3. Bevel cut  
Loosen the lever and tilt the saw blade to set the bevel  
angle (Refer to the previously covered Adjusting the  
bevel angle). Be sure to retighten the lever firmly to  
secure the selected bevel angle safely. Secure the work-  
piece with a vise. Switch on the tool without the blade  
making any contact and wait until the blade attains full  
speed. Then gently lower the handle to the fully lowered  
position while applying pressure in parallel with the  
blade. When the cut is completed, switch off the tool and  
WAIT UNTIL THE BLADE HAS COME TO A COM-  
PLETE STOP before returning the blade to its fully ele-  
vated position.  
CAUTION:  
Always be sure that the blade will move down to bevel  
direction during a bevel cut. Keep hands out of path of  
saw blade.  
During a bevel cut, it may create a condition whereby the  
piece cut off will come to rest against the side of the  
blade. If the blade is raised while the blade is still  
rotating, this piece may be caught by the blade, causing  
fragments to be scattered which is dangerous. The blade  
should be raised ONLY after the blade has come to a  
complete stop.  
21  
 
When pressing the handle down, apply pressure parallel  
to the blade. If the pressure is not parallel to the blade  
during a cut, the angle of the blade might be shifted and  
the precision of the cut will be impaired.  
4. Compound cutting  
Compound cutting is the process in which a bevel angle  
is made at the same time in which a miter angle is being  
cut on a workpiece. Compound cutting can be performed  
at angle shown in the table.  
Miter angle  
Left and Right 45˚  
Left and Right 52˚  
Bevel angle  
Left 0 - 45˚  
Left 0 - 40˚  
When performing compound cutting, refer to Press cut-  
ting, Miter cuttingand Bevel cutexplanations.  
5. Cutting crown and cove moldings  
Crown and cove moldings can be cut on a compound  
miter saw with the moldings laid flat on the turn base.  
001555  
There are two common types of crown moldings and one  
type of cove moldings; 52/38° wall angle crown molding,  
45° wall angle crown molding and 45° wall angle cove  
molding. See illustrations.  
52˚  
38˚  
45˚  
45˚  
45˚  
45˚  
1
2
3
1. 52/38° type crown molding  
2. 45° type crown molding  
3. 45° type cove molding  
22  
 
001556  
There are crown and cove molding joints which are  
made to fit Inside90° corners ((1) and (2) in Fig. A) and  
Outside90° corners ((3) and (4) in Fig. A).  
Measuring  
Measure the wall length and adjust workpiece on table to  
cut wall contact edge to desired length. Always make  
sure that cut workpiece length at the back of the work-  
piece is the same as wall length. Adjust cut length for  
angle of cut. Always use several pieces for test cuts to  
check the saw angles.  
(1) (2) (3)(4)  
1
2
Fig.A  
1. Inside corner  
2. Outside corner  
001557  
When cutting crown and cove moldings, set the bevel  
angle and miter angle as indicated in the table (A) and  
position the moldings on the top surface of the saw base  
as indicated in the table (B).  
1
(1)  
(2)  
(2)  
(1)  
(4)  
(2)  
(1)  
(3)  
2
(2)  
(1)  
(1)  
(2)  
Table (A)  
Molding  
Bevel angle  
Miter angle  
position in Fig. A 52/38˚ type 45˚ type 52/38˚ type 45˚ type  
1. Inside corner  
2. Outside corner  
For inside  
corner  
For outside  
corner  
(1)  
(2)  
(3)  
(4)  
Right 31.6˚ Right 35.3˚  
Left 31.6˚ Left 35.3˚  
Right 31.6˚ Right 35.3˚  
Left 33.9˚  
Left 30˚  
Table (B)  
Molding  
Molding edge against  
Finished piece  
position in Fig. A guide fence  
Ceiling contact edge should  
be against guide fence.  
Wall contact edge should be  
against guide fence.  
Ceiling contact edge should be be on the Right side  
against guide fence. of blade.  
Finished piece will  
be on the Left side  
of blade.  
For inside  
corner  
(1)  
(2)  
(3)  
Finished piece will  
For outside  
corner  
(4)  
23  
 
Example:  
In the case of cutting 52/38° type crown molding for  
position (1) in Fig. A:  
Tilt and secure bevel angle setting to 33.9°  
LEFT.  
Adjust and secure miter angle setting to 31.6°  
RIGHT.  
Lay crown molding with its broad back (hidden)  
surface down on the turn base with its CEILING  
CONTACT EDGE against the guide fence on  
the saw.  
The finished piece to be used will always be on  
the LEFT side of the blade after the cut has  
been made.  
24  
 
EN0002-1  
000031  
Compound Miter Saw  
Miter and Bevel Angle Settings  
Ceiling  
52˚  
38˚  
Wall to Crown Molding Angle: 52/38 degrees  
Wall Angle Bevel Angle Miter Angle  
Wall Angle Bevel Angle Miter Angle  
Wall Angle Bevel Angle Miter Angle  
(deg.)  
(deg.)  
43.0  
42.8  
42.5  
42.2  
41.9  
41.7  
41.4  
41.1  
40.8  
40.5  
40.2  
39.9  
39.6  
39.3  
39.0  
38.7  
38.4  
38.1  
37.8  
(deg.)  
46.8  
46.3  
45.7  
45.1  
44.6  
44.0  
43.5  
42.9  
42.4  
41.9  
41.3  
40.8  
40.3  
39.8  
39.2  
38.7  
38.2  
37.7  
37.2  
(deg.)  
(deg.)  
30.1  
29.7  
29.4  
29.0  
28.7  
28.3  
28.0  
27.6  
27.2  
26.9  
26.5  
26.1  
25.8  
25.4  
25.0  
24.7  
24.3  
23.9  
23.6  
(deg.)  
26.9  
26.5  
26.1  
25.7  
25.3  
24.9  
24.5  
24.1  
23.7  
23.3  
22.9  
22.6  
22.2  
21.8  
21.4  
21.0  
20.7  
20.3  
19.9  
(deg.)  
(deg.)  
15.3  
14.9  
14.5  
14.1  
13.7  
13.3  
12.9  
12.5  
12.2  
11.8  
11.4  
11.0  
10.8  
10.2  
9.8  
(deg.)  
101  
141  
12.3  
12.0  
11.6  
11.3  
11.0  
10.7  
10.3  
10.0  
9.7  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
102  
103  
104  
105  
106  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118  
119  
142  
143  
144  
145  
146  
147  
148  
149  
150  
151  
152  
153  
154  
155  
156  
157  
158  
159  
9.4  
9.0  
8.7  
8.4  
8.1  
7.8  
9.4  
7.5  
9.0  
7.1  
8.6  
6.8  
8.3  
6.5  
79  
37.4  
36.8  
23.2  
19.6  
160  
7.9  
6.2  
120  
121  
122  
123  
124  
125  
126  
127  
128  
129  
130  
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
37.1  
36.8  
36.5  
36.2  
35.8  
35.5  
35.2  
34.9  
34.5  
34.2  
36.3  
35.8  
35.3  
34.8  
34.4  
33.9  
33.4  
33.0  
32.5  
32.1  
22.8  
22.5  
22.1  
21.7  
21.3  
21.0  
20.6  
20.2  
19.8  
19.5  
19.2  
18.8  
18.5  
18.1  
17.8  
17.4  
17.1  
16.7  
16.4  
16.0  
161  
162  
163  
164  
165  
166  
167  
168  
169  
170  
7.5  
7.1  
6.7  
6.3  
5.9  
5.5  
5.1  
4.7  
4.3  
3.9  
5.9  
5.6  
5.3  
4.9  
4.6  
4.3  
4.0  
3.7  
3.4  
3.1  
33.9  
31.6  
131  
19.1  
15.7  
171  
3.5  
2.8  
90  
91  
92  
93  
94  
95  
96  
97  
98  
99  
33.5  
33.2  
32.8  
32.5  
32.2  
31.8  
31.5  
31.1  
30.8  
30.4  
31.2  
30.7  
30.3  
29.9  
29.4  
29.0  
28.6  
28.2  
27.7  
27.3  
132  
133  
134  
135  
136  
137  
138  
139  
140  
18.7  
18.3  
17.9  
17.6  
17.2  
16.8  
16.4  
16.0  
15.8  
15.3  
15.0  
14.6  
14.3  
14.0  
13.6  
13.3  
13.0  
12.8  
172  
173  
174  
175  
176  
177  
178  
179  
180  
3.2  
2.8  
2.4  
2.0  
1.6  
1.2  
0.8  
0.4  
0.0  
2.5  
2.2  
1.8  
1.5  
1.2  
0.9  
0.6  
0.3  
0.0  
100  
25  
 
EN0003-1  
000032  
Compound Miter Saw  
Miter and Bevel Angle Settings  
Ceiling  
45˚  
45˚  
Wall to Crown Molding Angle: 45 degrees  
Wall Angle Bevel Angle Miter Angle  
Wall Angle Bevel Angle Miter Angle  
Wall Angle Bevel Angle Miter Angle  
(deg.)  
(deg.)  
37.8  
37.5  
37.3  
37.1  
36.8  
36.6  
36.4  
36.1  
35.9  
35.6  
35.4  
35.1  
34.9  
34.6  
34.4  
34.1  
33.9  
33.6  
33.3  
(deg.)  
50.8  
50.2  
49.6  
49.1  
48.5  
48.0  
47.4  
46.9  
46.4  
45.8  
45.3  
44.8  
44.2  
43.7  
43.2  
42.7  
42.1  
41.6  
41.1  
(deg.)  
(deg.)  
26.7  
26.4  
26.1  
25.8  
25.5  
25.2  
24.9  
24.6  
24.2  
23.9  
23.6  
23.3  
23.0  
22.7  
22.3  
22.0  
21.7  
21.4  
21.0  
(deg.)  
30.2  
29.8  
29.4  
28.9  
28.5  
28.1  
27.6  
27.2  
26.8  
26.3  
25.9  
25.5  
25.1  
24.7  
24.3  
23.8  
23.4  
23.0  
22.6  
(deg.)  
(deg.)  
13.7  
13.3  
13.0  
12.6  
12.3  
11.9  
11.6  
11.2  
10.9  
10.5  
10.2  
9.8  
(deg.)  
101  
141  
14.1  
13.7  
13.3  
12.9  
12.6  
12.2  
11.8  
11.5  
11.1  
10.7  
10.4  
10.0  
9.6  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
102  
103  
104  
105  
106  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118  
119  
142  
143  
144  
145  
146  
147  
148  
149  
150  
151  
152  
153  
154  
155  
156  
157  
158  
159  
9.5  
9.2  
9.3  
8.8  
8.9  
8.5  
8.5  
8.1  
8.2  
7.8  
7.8  
7.4  
7.5  
79  
33.1  
40.6  
20.7  
22.2  
160  
7.1  
7.1  
120  
121  
122  
123  
124  
125  
126  
127  
128  
129  
130  
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
32.8  
32.5  
32.3  
32.0  
31.7  
31.4  
31.1  
30.9  
30.6  
30.3  
40.1  
39.6  
39.1  
38.6  
38.1  
37.7  
37.2  
36.7  
36.2  
35.7  
20.4  
20.0  
19.7  
19.4  
19.1  
18.7  
18.4  
18.1  
17.7  
17.4  
21.8  
21.4  
21.0  
20.6  
20.2  
19.8  
19.4  
19.0  
18.6  
18.2  
161  
162  
163  
164  
165  
166  
167  
168  
169  
170  
6.7  
6.4  
6.0  
5.6  
5.3  
4.9  
4.6  
4.2  
3.9  
3.5  
6.7  
6.4  
6.0  
5.7  
5.3  
5.0  
4.6  
4.3  
3.9  
3.5  
30.0  
35.3  
131  
17.1  
17.9  
171  
3.2  
3.2  
90  
91  
92  
93  
94  
95  
96  
97  
98  
99  
29.7  
29.4  
29.1  
28.8  
28.5  
28.2  
27.9  
27.6  
27.3  
27.0  
34.8  
34.3  
33.9  
33.4  
32.9  
32.5  
32.0  
31.6  
31.1  
30.7  
132  
133  
134  
135  
136  
137  
138  
139  
140  
16.7  
16.4  
16.0  
15.7  
15.4  
15.0  
14.7  
14.3  
14.0  
17.5  
17.1  
16.7  
16.3  
15.9  
15.6  
15.2  
14.8  
14.4  
172  
173  
174  
175  
176  
177  
178  
179  
180  
2.8  
2.5  
2.1  
1.8  
1.4  
1.1  
0.7  
0.4  
0.0  
2.8  
2.5  
2.1  
1.8  
1.4  
1.1  
7.0  
0.4  
0.0  
100  
26  
 
001846  
6. Cutting repetitive lengths  
When cutting several pieces of stock to the same length,  
ranging from 220 mm (8-5/8) to 365 mm (14-3/8), use  
of the set plate (optional accessory) will facilitate more  
efficient operation. Install the set plate on the holder  
(optional accessory) as shown in the figure.  
Align the cutting line on your workpiece with either the  
left or right side of the groove in the kerf board, and while  
holding the workpiece from moving, move the set plate  
flush against the end of the workpiece. Then secure the  
set plate with the screw. When the set plate is not used,  
loosen the screw and turn the set plate out of the way.  
1
2
3
1. Set plate  
2. Holder  
3. Screw  
NOTE:  
Use of the holder-rod assembly (optional accessory)  
allows cutting repetitive lengths up to 2,200 mm (7.2 ft.)  
approximately.  
001847  
Carrying tool  
Make sure that the battery cartridge is removed. Secure the  
blade at 0° bevel angle and the turn base at right miter angle  
fully. Lower the handle fully and lock it in the lowered position  
by pushing in the stopper pin.  
1
1. Stopper pin  
001814  
Carry the tool by carrying grip as shown in the figure. If you  
remove the holders, dust bag, etc., you can carry the tool  
more easily.  
CAUTION:  
Always secure all moving portions before carrying the  
tool.  
Stopper pin is for carrying and storage purposes only  
and not for any cutting operations.  
MAINTENANCE  
CAUTION:  
Always be sure that the tool is switched off and the  
battery cartridge is removed before attempting to  
perform inspection or maintenance.  
27  
 
WARNING:  
Always be sure that the blade is sharp and clean for the  
best and safest performance.  
Adjusting the cutting angle  
This tool is carefully adjusted and aligned at the factory, but  
rough handling may have affected the alignment. If your tool  
is not aligned properly, perform the following:  
001815  
1. Miter angle  
1
2
Loosen the grip which secures the turn base. Turn the  
turn base so that the pointer points to 0° on the miter  
scale. Then turn the turn base slightly clockwise and  
counterclockwise to seat the turn base in the 0° miter  
notch. (Leave as it is if the pointer does not point to 0°.)  
Loosen the hex bolts securing the guide fence using the  
socket wrench.  
1. Guide fence  
2. Hex bolt  
001816  
Lower the handle fully and lock it in the lowered position  
by pushing in the stopper pin. Square the side of the  
blade with the face of the guide fence using a triangular  
rule, try-square, etc. Then securely tighten the hex bolts  
on the guide fence in the order from the right side.  
1
1. Triangular rule  
001817  
Make sure that the pointer points to 0° on the miter  
scale. If the pointer does not point to 0°, loosen the  
screw which secures the pointer and adjust the pointer  
so that it will point to 0°.  
1
3
2
1. Screw  
2. Miter scale  
3. Pointer  
28  
 
2. Bevel angle  
001818  
(1) 0° bevel angle  
Lower the handle fully and lock it in the lowered  
position by pushing in the stopper pin. Loosen the  
lever at the rear of the tool.  
1
Turn the 0° bevel angle adjusting bolt (lower bolt) on  
the right side of the arm two or three revolutions  
counterclockwise to tilt the blade to the right.  
4
3
2
1. Sub arm  
2. Arm  
3. 0° bevel angle adjusting bolt  
4. Lever  
001819  
Carefully square the side of the blade with the top  
surface of the turn base using the triangular rule,  
try-square, etc. by turning the 0° bevel angle adjust-  
ing bolt clockwise. Then tighten the lever securely.  
1
2
3
1. Triangular rule  
2. Saw blade  
3. Top surface of turn base  
001820  
Make sure that the pointer on the arm point to 0° on  
the bevel scale on the arm sub. If it does not point to  
0°, loosen the screw which secures the pointer and  
adjust the pointer so that it will point to 0°.  
3
1
2
4
1. Pointer  
2. Screw  
3. Arm  
4. Sub arm  
001821  
(2) 45° bevel angle  
Adjust the 45° bevel angle only after performing 0°  
bevel angle adjustment. To adjust left 45° bevel  
angle, loosen the lever and tilt the blade to the left  
fully. Make sure that the pointer on the arm points to  
45° on the bevel scale on the arm holder. If the  
pointer does not point to 45°, turn the 45° bevel  
angle adjusting bolt (upper bolt) on the right side of  
the arm until the pointer points to 45°.  
1
1. 45° bevel angle adjusting bolt  
29  
 
001145  
Replacing carbon brushes  
Remove and check the carbon brushes regularly. Replace  
when they wear down to the limit mark. Keep the carbon  
brushes clean and free to slip in the holders. Both carbon  
brushes should be replaced at the same time. Use only iden-  
tical carbon brushes.  
1
1. Limit mark  
001822  
Use a screwdriver to remove the brush holder caps. Take out  
the worn carbon brushes, insert the new ones and secure  
the brush holder caps.  
After replacing brushes, insert the battery cartridge into the  
tool and break in brushes by running tool with no load for  
about 1 minute. Then check the tool while running and elec-  
tric brake operation when releasing the switch trigger. If elec-  
tric brake is not working well, ask your local Makita service  
center for repair.  
1
2
1. Screwdriver  
2. Brush holder cap  
After use  
After use, wipe off chips and dust adhering to the tool  
with a cloth or the like. Keep the blade guard clean  
according to the directions in the previously covered  
section titled Blade guard. Lubricate the sliding  
portions with machine oil to prevent rust.  
To maintain product SAFETY and RELIABILITY, repairs, any  
other maintenance or adjustment should be performed by  
Makita Authorized or Factory Service Centers, always using  
Makita replacement parts.  
30  
 
ACCESSORIES  
CAUTION:  
These accessories or attachments are recommended for  
use with your Makita tool specified in this manual. The  
use of any other accessories or attachments might  
present a risk of injury to persons. Only use accessory  
or attachment for its stated purpose.  
If you need any assistance for more details regarding these  
accessories, ask your local Makita service center.  
Carbide-tipped saw blades  
Miter saw blades  
For smooth and precise cutting in various  
materials.  
Auxiliary plate  
Vise assembly (Horizontal vise)  
Vertical vise  
Socket wrench 10  
Holder set  
Holder assembly  
Holder rod assembly  
Set plate  
Dust bag  
Triangular rule  
Lock-off button (2 pcs.)  
31  
 
Memo  
32  
 
Stamp  
Timbre  
Makita Canada Inc.  
1950 Forbes Street,  
Whitby, Ontario  
L1N 7B7  
Fold  
 
Your answers to the following questions are appreciated.  
1.This product was purchased from?  
3. How did you first learn of Makita Power Tools?  
Hardware/lumber Store  
Tool Distributor  
Industrial Supply  
Other (  
Magazine/Newspaper  
From dealer  
Catalog  
Other (  
)
)
Store display  
2. Use of the product is intended for?  
4. Most favored points are?  
Construction trade  
Home maintenance  
Other (  
Design  
Makita Brand  
Power  
Industrial maintenance  
)
Features  
Size  
Other (  
)
Price  
5. Any comments?  
Certificate of Warranty  
Mail to Makita  
Date Purchased  
Model No.  
Serial No.  
Month  
Day  
Year 20  
Male Female  
Single  
Married  
Initial Last Name  
Street Address  
City  
Province  
Postal Code  
Under 19  
20-29  
30-39  
40-49  
Over 50  
AGE:  
Occupation:  
Dealer's Name & Address:  
 
Paste Paste Paste Paste Paste Paste  
Paste  
Paste  
Factory Service Centres  
Head Office:  
1950 Forbes St., Whitby, Ontario, L1N 7B7  
(905) 571 - 2200 1-800-263-3734  
Regional Office:  
11771 Hammersmith Way, Richmond  
B.C. V7A 5H6  
(604) 272 - 3104 1-800-663-0909  
Regional Office:  
(Montreal)  
6389 boul. Couture, St. Leonard, Quebec  
H1P 3J5  
(514) 323 - 1223 1-800-361-7049  
Dartmouth:  
202 Brownlow Avenue  
Dartmouth, N.S., B3B 1T5  
(902) 468 - 7064 1-888-625-4821  
Ville St. Laurent:  
(Montreal)  
1140 Rue Bégin, Ville St. Laurent, Quebec  
H4R 1X1  
(514) 745 - 5025 1-888-745-5025  
Les Saules:  
(Quebec)  
1200 St. Jean Baptiste, Unit 106, Les Saules,  
Quebec, G2E 5E8  
(418) 871 - 5720 1-800-663-5757  
Nepean:  
(Ottawa)  
203 Colonnade Road, Unit #6, Nepean,  
Ontario K2E 7K3  
(613) 224 - 5022 1-888-560-2214  
Whitby:  
1950 Forbes St., Whitby, Ontario, L1N 7B7  
(905) 571 - 2200 1-800-263-3734  
London:  
317 Adelaide St. S., Unit 117, London,  
Ontario, N5Z 3L3  
(519) 686 - 3115 1-800-571-0899  
Mississauga:  
Calgary:  
6350 Tomken Rd., Unit 8, Mississauga,  
Ontario, L5T 1Y3  
(905) 670 - 7255 1-888-221-9811  
#8-6115 Fourth St. S.E., Calgary  
Alberta, T2H 2H9  
(403) 243 - 3995 1-800-267-0445  
Edmonton:  
Richmond:  
Coquitlam:  
Winnipeg:  
Saskatoon:  
11614-149 Street, Edmonton, Alberta,  
T5M 3R3  
(780) 455 - 6644 1-888-455-6644  
11771 Hammersmith Way, Richmond, B.C.,  
V7A 5H6  
(604) 272 - 3104 1-800-663-0909  
2131 Hartley Ave., #103  
Coquitlam, B.C. V3K 2Z3  
(604) 525 - 7434 1-800-266-7738  
1670 St. James Street, Winnipeg, Manitoba,  
R3H 0L3  
(204) 694 - 0402 1-800-550-5073  
206A-2750 Faithful Avenue Saskatoon,  
Saskatchewan, S7K 6M6  
(306) 931 - 0111 1-888-931-0111  
For the authorized service centre nearest you please refer to the local yellow pages directory under toolsor con-  
tact our customer service department (Tel) 1-800-263-3734  
CUSTOMER RECORD  
When you need service...  
DATE  
Explain the problem in a letter  
PURCHASED:  
Enclose the letter with the tool  
DEALERS NAME  
Package carefully and send prepaid  
& ADDRESS:  
to the nearest Makita factory or  
authorized service centre  
MODEL NO.:  
SERIAL NO.:  
35  
 
MAKITA LIMITED ONE YEAR WARRANTY  
Warranty Policy  
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from  
workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during  
this one year period, return the COMPLETE tool, freight prepaid, to one of Makitas Factory or Authorized Service Centres.  
If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace)  
without charge.  
This Warranty does not apply:  
where normal maintenance is required,  
repairs have been made or attempted by others,  
the tool has been abused, misused or improperly maintained,  
alterations have been made to the tool.  
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM  
THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS  
WARRANTY.  
The Makita Warranty is the only and the entire written warranty given by Makita for the Makita tools. No dealer or his agent  
or employee is authorized to extend or enlarge upon this warranty by any verbal or written statement or advertisement.”  
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES INCLUDING IMPLIED WARRANTIES OF  
MERCHANTABILITYAND FITNESS FOR A SPECIFIC PURPOSE,AFTER THE ONE YEAR TERM OF THIS WARRANTY.  
This Warranty gives you specific rights. The provisions contained in this warranty are not intended to limit, modify, take away  
from, disclaim or exclude any warranties set forth in any provincial legislation. To the extent required by law, the provisions in  
any provincial or federal legislation with respect to warranties take precedence over the provisions in this warranty.”  
Makita Corporation of America  
2650 Buford Hwy., Buford, GA 30518  
884307A238  
 

La Crosse Technology Clock 515 1316 User Manual
La Crosse Technology Weather Radio WS 1913 User Manual
Land Pride Lawn Mower ZXT PRo User Manual
LG Electronics Mouse LSM 100 User Manual
Life Fitness Treadmill 97twez User Manual
Makita Grinder BGA402 User Manual
Mark Feldstein Assoc Indoor Furnishings TLFC04 User Manual
Maytag Washer Dryer MD491 User Manual
Metrologic Instruments Scanner MS9530 Series User Manual
MicroNet Technology Network Router SP915G User Manual