Manitowoc Ice Ice Maker K00385 User Manual

K00385 ADAPTER KIT  
Installation Instructions  
The K00385 kit is used for installing S-1474 or S-1870 ice machines on a B-970 bin.  
(Refer to Sheet 2 of 3 for pre-installation instructions.)  
1. Note: Bin must be level before installation of ice machine.  
A. Remove the foam tape from the front and sides of the bin where the stainless support/deflector will be located.  
Use the support to reference the areas where the tape should be removed.  
B. Place the support on the front edge of the bin and position as far forward as possible.  
C. Locate the four pieces of the 2” long, 3/4” wide foam tape in the front corners, as shown.  
D. Place the fillers on the bin, as shown. Make sure the two holes from the stainless support/deflector and fillers are  
aligned on the side.  
E. Using the fillers as templates, drill three 5/32” (4 mm.) holes, .500” (12.7 mm.) deep maximum, in the bin.  
Warning: Do not drill through the interior liner. Attach each filler with three 10-24 x .500” screws provided.  
F. Apply foam tape to the front and back of the bin between the fillers. Note: All other required foam tape comes  
preassembled with the stainless support/deflector and fillers.  
G. Note: It is recommended to RTV intersections and along the inside edge of the foam tape to prevent water  
tracking.  
2. Refer to ice machine installation manual for ice machine installation procedures.  
.75” Wide Foam Tape  
Filler  
Filler  
Filler  
.75” Wide Foam Tape  
INSTALLER: It is  
recommended to RTV  
#10-24 x .50”L  
Screws Typ  
intersections and along inside  
edge of foam tape to prevent  
water tracking  
Stainless Steel  
Support/Deflector  
.75” x 2.00”L Foam Tape  
Typ both front corners  
Manitowoc Ice, Inc.  
2110 South 26th Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA  
000002544  
Sheet 1 of 3  
06/13/07  
Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879  
 
Installing Ice deflector  
1. Locate correct position for the deflector.  
If the ice machine is installed, remove the water trough to obtain easier access.  
The deflector must be located in the center of the drop zone.  
Location is 11” from the left edge of the ice machine to the left edge of the mounting bracket.  
2. Cut and remove the foam tape on the front and back of the bin where the deflector will be located.  
3. Remove any residual adhesive; areas must be clean and dry.  
4. Remove protective covering from the two sided tape on each deflector bracket.  
5. Install the deflector bracket.  
Distribute the mounting bracket equally on the front and back of the bin.  
Locate the retaining pin to the back.  
Press the mounting bracket into place.  
6. Trim supplied foam tape to length of cuts from step 2 and apply over the top of the bracket. Seal edges  
where deflector mounting bracket meets foam tape with silicone sealant to prevent water leakage.  
7. Install the deflector into the mounting bracket.  
Align tabs and slide the deflector toward the front of the bin.  
Insert retaining pin into hole in the mounting bracket to lock deflector in place.  
Reinstall water trough if removed in step 1.  
Water  
Pump  
Location  
Water Trough  
Located Behind  
Splash  
Splash Shield  
Shield  
Ice Deflector  
000002544  
Sheet 3 of 3  
06/13/07  
 

Kyocera Fax Machine FS 3640MFP User Manual
Lanzar Car Audio Car Stereo System OPTIMC90 User Manual
Lenovo Computer Drive 43R2018 User Manual
LG Electronics Blu ray Player BD670 User Manual
Life Fitness Treadmill AK58 00610 0000 User Manual
Lightolier Indoor Furnishings 1102TF User Manual
Lightolier Indoor Furnishings 1102TH1R User Manual
Mackie Portable Speaker SA1232 User Manual
Marquis Tablet MP977 User Manual
Microsoft Video Game Console X10 99979 User Manual