Operating Instructions
Tumble dryer
Dear Maytag customer,
Thank you for choosing this quality product from
Scandinavia, made in Vara, Sweden.
We want you to feel assured that the inside of your new
machine is just as good as the outside and that the ethics and
standards that went into the production of this machine are
just as high as the quality and performance that you will
receive from it. We hope that this product will give you many
years of pleasure.
To get the most out of your new machine, we recommend that
you read the Use & Care Guide before using the machine.
MDE9651
Before using your machine for the first time
Note!
Do not tumble-dry
When starting the tumble dryer for the first
time or after a long period without use, you
may notice a slight thumping sound.This is
completely normal and will stop after a few
loads.
Certain materials are sensitive to tumble-
drying. Always check and follow an item’s
laundry label.You can read more on page 9,
“Before tumble-drying”.
See the Quick guide on the last page.
3
Safety instructions
General
Transport/Winter storage
• Read and keep the Use & Care Guide!
• Electrical installation, if required, should
be carried out by qualified professionals.
• The machine should only be used for
tumble-drying as described in these
instructions.
If you need to move your machine or store it
over the winter in unheated premises, then
make sure you drain the condensed water
container beforehand.
Packing material
• Repairs and maintenance relating to
safety or performance must be carried out
by a qualified professional.
Sort waste in accordance with local guide-
lines.
• Damaged mains cables must only be
replaced by a qualified professional.
• Sufficient ventilation is required to pre-
vent smoke from open fires or fumes
from equipment burning other fuels being
sucked into the room.
Disposal
When the machine has reached the end of
its service life and is to be disposed of, it
should immediately be made unusable.
Contact your local authority for information
about where your old machine should be
disposed of and recycled in the proper way.
The machine is manufactured and labelled
to facilitate recycling.
Installation
See the “Installation” chapter.
Safety
Caution
The machine must not be used for drying
items that have been dry-cleaned at home
or fabrics that may contain residues of flam-
mable liquids.
During operation, the back of the tumble
dryer will get very hot. Leave the machine to
cool completely before touching the back.
The tumble dryer is protected by an over-
heating cut-out.This shuts off the machine
if the temperature gets too high.
A float shuts off the machine in the event
of a blockage in the condensed water hose
or if there is a risk of the condensed water
container overflowing.
Stopping a programme
You can stop a drying programme by:
• opening the door; the drum stops auto-
matically,
• or by pressing the main power switch.
• When you want to resume tumble-drying,
simply close the door and press the Start/
Stop button.
• You can also stop a programme by press-
ing the Start/Stop button for three sec-
onds.
4
Child safety
General
Do not allow children to play with the
tumble dryer.
The tumble dryer has a magnetic catch,
allowing the door to be opened from the
inside.The door has a door-switch that auto-
matically stops the tumble dryer when the
door is opened.The tumble dryer does not
start automatically when the door closes
(e.g. if a child closes the door from inside).
5
Parts of the tumble dryer
3
4
2
1
6
5
7
1.
2.
3.
4.
Fluff filter holder
Type plate
Condensed water container
Panel
5.
6.
7.
8.
Outer door
Fan (behind the front plate)
Condenser (behind the front plate)
Fluff filter
8
6
Front panel
5
2
1
6
3
4
7
1.
Main power switch
2-4. Options buttons
5.
6.
7.
Programme selector
Display
Start/Stop
Options buttons
2
4
3
2.
3.
4.
Button for selecting Low Temperature
Button for selecting Anti-crease Programme
Button for selecting Delayed Start 5 h
7
Advice and tips before you tumble-dry
Here are some tips that may help you before you begin tumble-drying.
Has it been spun?
Items to be tumble-dried should be spun at
1000 rpm or faster. Better spinning saves
both energy and drying time.
Laundry labels
Materials that can be tumble-dried
This symbol means that the material is suit-
able for tumble-drying. Fabrics best suited
to tumble-drying are cotton fabrics, terry
cloth and synthetic fibres. Garments will be
softer and lighter when tumbled than when
hung out to dry.
Note!
Wear to fabrics in the tumble dryer is in-
significant.The fluff that gets caught in the
fluff filter is dust and fibre remnants formed
when the items are used.
Materials that must not be
tumble-dried
This symbol means that the material is not
suitable for tumble-drying.
Certain materials may melt or become a fire
hazard if exposed to heat, and others lose
their shape or shrink.
And do not tumble-dry...
• materials labelled “Do not dry near heat”,
• garments that have been dry-cleaned at
home,
• foam plastic,
• fibreglass material,
• wool must not be tumble-dried due to the
risk of felting.
8
Tumble-drying
Below are step-by-step instructions to
help you achieve the best possible tumble-
drying results.
Iron Dry
This programme shuts off the heat once
the load is just damp enough for ironing or
pressing.
Sort your fabrics
Timed dry 60 min
You will achieve the most uniform dry-
ing results if the items are the same
material.
The Timed dry programme has a fixed dry-
ing time and tumble-dries the load for 60
minutes.
Do up zips and buttons, fasten belts, sort
the items and adjust load and temperature.
Air fluff 60 min
Use the Air fluff programme when you just
want to refresh, air or soften up items.
Turn on the main power
switch
Select options
Open the door, load the items
and then close the door
By selecting options, you can tailor
5 drying programmes to suit your own
laundry requirements.
Select programme
The machine remembers which settings
and options you choose for each pro-
gramme and uses these
The choice of programme depends
on what you intend to do with the
items after tumbling.The programme
options are Extra Dry, Dry, Normal Dry, Iron
Dry, Timed programme and Airing.
(with one exception
- Delayed start) the next
time you select the pro-
gramme in question.You
Extra Dry
can, of course, change
This programme is for items that are par-
ticularly difficult to dry, e.g. jeans with very
thick seams.
them again if you wish.
Low temperature
Select or deselect Low Temperature by
pressing the Temperature button.
Once Low Temperature has been selected,
the red field next to the button lights up.
Note!
Knit fabrics in particular are prone to shrink-
age. Use the Dry, Normal Dry or Iron Dry
programmes for such items. Stretch clothes
back into shape immediately after drying.
Anti-crease
This option means that the drum will rotate
three seconds per minute for two hours
once the drying programme has finished.
This option prevents the items remaining in
the same position and becoming creased.
A useful feature if you are not able to re-
move the load as soon as tumble-drying
has finished.
Dry, Normal Dry
These programmes shut off the heat once
the load is dry without being “bone-dry”.
The Dry programme shuts off the heat
slightly later than Normal Dry. Use trial and
error to find out what works best. Use these
programmes when you want items to be
completely dry.
A lighted red field by the button indicates
that the Anti-crease option has been acti-
vated.
9
Delayed Start
Drying programme finished
Select or deselect this option by pressing
the Delayed Start button.The machine will
start the programme 5 hours after you se-
lect this option + the Start/Stop button.
A lighted red field by the button indicates
that the option has been activated. If you
change your mind, press the Start/Stop but-
ton for three seconds.You can now start the
machine as usual
The text
in the display indicates
7that the programme has finished.
If the Anti-crease option has been
selected, the drum will rotate every minute
for 2 hours after cooling.
Important!
• Clean the fluff filter after each load.
• Drain the condensed water container after
each load.
Press the Start button
Caution!
6
If the fluff filter becomes clogged, the ma-
chine’s automatic overheating cut-out may
be triggered.To enable the machine to be
restarted, the filter must be cleaned and
the machine allowed to cool for around 30
minutes.
Drying time remaining
An estimate of the remaining drying time
will be shown in the display within 2 min-
utes of the drying programme starting. For
example, 1:35 means that approximately 1
hour and 35 minutes remain until the load
achieves the selected level of dryness. If
the Anti-crease option has been selected,
the drum will rotate every minute for 2 hours
after cooling.
Cleaning the fluff filter
1. Grasp the filter handle and pull it towards
you.
2. Pull the filter out of its holder.
3. Open the filter and remove the fluff by
If you want to stop or change a
programme.
hand.
Press and hold the Start/Stop button for 3
seconds.The red field next to the button
goes out.
4. Fold the filter up and re-insert it into its
holder.The filter may need to be cleaned
if limescale deposits occur, see “Care and
cleaning” chapter.
Note!
The programme is not affected if the pro-
gramme selector is changed after the pro-
gramme starts.
To load or remove washing
2
1
If you want to load or remove washing
once you have started the machine, open
the door and the machine will stop auto-
matically. Load more washing, close the
door and press the Start/Stop button.
10
Draining the condensed water
container
The condensed water container must be
drained after each load.
Remove the condensed water container,
empty out the water and replace the con-
tainer.
If the condensed water container becomes
full to overflowing, the programme is inter-
rupted and
is shown in the display. Emp-
ty the container and press the Start/Stop
button to restart the programme. See also
Error Messages on page 16 in the “Trouble-
shooting” chapter.
Note!
Do not remove the condensed water con-
tainer while the machine is switched on.
Advice!
As the condensed water is decalcified, it
can be used in steam irons. Pour through a
coffee filter.
Automatic drain
If you want the water to drain automatically,
please see Installation.
Once drying has finished
Switch off the main power switch.
8Remove the clothes, and close the
door to prevent small children from
climbing into the machine.
11
Consumption values
For the consumption values given below, the following prerequisites apply:
Temperature of intake air:
Moisture content of intake air:
Drying temperature:
20 °C.
65 %.
Normal or low.
2500 W.
Element power:
Before tumble-drying, cotton fabrics are spun at 800 and 1600 rpm (long spin).
Before tumble-drying, other fabrics (crease-resistant and acrylic) are spun at 800 rpm (short
spin).
Energy
Programme
consumption
time (approx. min.)
Max.load (approx. kWh)
Temperature (kg) 800 rpm 1600 rpm 800 rpm 1600 rpm
Programme
Extra Dry
Dry
Material
Cotton, linen
Cotton, linen
Normal
Normal
6.0
6.0
5.0
4.2
4.1
3.2
155
130
130
100
Crease-resistant,
Dry
polyester/cotton
Normal
Normal
3.0
6.0
1.8
3.8
-
60
120
-
95
Normal Dry
Cotton, linen
2.9
Crease-resistant,
polyester/cotton
Normal Dry
Normal
3.0
1.7
-
55
-
Acrylic, rayon,
acetate
Cotton, linen
Normal Dry
Iron Dry
Low
Normal
3.0
6.0
2.1
3.4
-
80
105
-
75
2.3
12
Care and cleaning
Cleaning the fluff filter
Draining the condensed water
container
The fluff filter must be cleaned after each
load.
If you have very hard water, this can cause
limescale deposits in the fluff filter. Check
for any limescale deposits when cleaning
the fluff filter and, if necessary, wash down
the filter by hand.
The condensed water container must be
drained after each load.
Remove the con-
densed water con-
tainer, empty out the
water and replace
1. Grasp the filter handle and pull it towards
you.
the container.
If the condensed
water container
2. Pull the filter out of its holder.
becomes full to
overflowing, the programme is interrupted
and the error message F1 is shown in the
display. Empty the container and press the
Start/Stop button to restart the programme.
See also Error Messages on page 16 in the
“Troubleshooting” chapter.
Note!
2
1
Do not remove the condensed water con-
tainer while the machine is switched on.
Cleaning the outside of the
machine
Clean the outside of the machine and the
programme panel with a mild cleaner. Do
not use any solvents, as these can damage
the machine. Do not hose down or spray
the machine with water.
3. Open the filter and remove the fluff from
all sides by hand. Use a soft dry cloth to
remove any coating.
Note!
Do not allow dust to accumulate around the
machine. Keep the area around the tumble
dryer clean and cool; dust, heat and mois-
ture prolong drying times.
4. Replace the filter in its holder.
Note!
If you have hard water, the filter should be
washed down with water to get rid of any
limescale deposits.
Dry the filter carefully with a towel.
13
Cleaning the condenser
The condenser should be cleaned at least
three times a year. If you have pets, the
condenser must be cleaned more frequent-
ly.
5. Replace the condenser. When reinstall-
ing the condenser, check that it is replaced
in the correct way.The top of the condenser
is labelled “upp”, “up” and “oben”.
UPP
UP
OBEN
1. Switch off the main power switch.
2. Remove the front plate.
6. Replace the front plate.
2
2
2
2
3. Open the condenser panel by turning the
two knobs anticlockwise.
1
4. Remove the condenser and rinse the
lamellas clean using a hand shower, for
example. Do not poke around in the lamella
springs, as you may damage the condens-
er. Do not use pointed metal objects during
cleaning.
Note!
Do not put the condenser in a dishwasher.
14
Troubleshooting
Error messages
The machine will not start
Check
• If F1 flashes in the display, the condensed
water container is full.
• that the outer door is properly closed
• that the main power switch is pressed
• that you have set the programme correctly
• that the Delayed Start option has not been
selected. If so, the time remaining until start
will be shown in full hours in the display
(e.g. 5, 4, 3h).To cancel the programme,
see page 10
Empty the container and restart.
• If F2 flashes in the display, the maxi-
mum permitted programme time has been
reached. For remedial action, read “Drying
takes too long” in the “Troubleshooting” sec-
tion.
• that any plug is connected
• that your home’s fuses (circuit breakers)
are intact, swap two circuit breakers.You
cannot always tell from outside if a circuit
breaker is broken
• that the overheating cut-out has not been
triggered (see below).
Overheating cut-out
The overheating cut-out shuts off the tum-
ble dryer if the temperature is too high, e.g.
because dust is clogging the fluff filter.
• Clean the filter.
• Check also that the condensed water
container is not full and, if necessary, clean
the condenser. See “Care and cleaning” on
page 14.
• The overheating cut-out will reset auto-
matically once the machine has cooled.
Drying takes too long
• Empty the condensed water container
and check that neither the fluff filter nor
the condenser is clogged. See “Care and
cleaning” on page 14.
• Prolonged drying times may also be due
to the condenser dryer being placed in a
room that is too small and the air in the
room (cooling air) being too hot.
• Make sure that the tumble dryer has ac-
cess to more cold air, e.g. by opening doors
and/or windows.
15
Technical information
Technical data
Height:
850 mm
595 mm
585 mm
47 kg
Width:
Depth:
Weight:
Cylinder volume:
Max. drying capacity:
RPM:
Rated power:
Drying drum material:
Outer casing material:
111 l
6.0 kg
52 rpm
See type plate.
Stainless steel.
Powder-coated and hot-galvanized sheet
steel or stainless steel.
Setup:
Drain:
Stacking or freestanding.
2.0 m rubber hose
Standard tests
Europe:
Drying performance:
EN 611 21 (95/13/EEC).
Dry, 6.0 kg cotton, temperature Normal.
EN 611 21 (95/13/EEC).
Energy declaration:
Dry, 6.0 kg cotton, temperature Normal.
The machine has been tested for single-
phase 10/16A.
IEC 60 704-2-6.
Test method noise measurement:
16
Service
Before contacting
the service division,
you should find out whether the fault is
anything you can take care of yourself. See
the chapters “Troubleshooting” and “Care
and cleaning”. If you do need to contact
the service division after all, make sure you
know the model designation, type designa-
tion and serial number.
The model designation can be found in the
stamped hole on the first page of the Use &
Care.Type designation and serial number
can be found on the type plate.
Type plate
17
Installation
Positioning the tumble dryer
The tumble dryer can be positioned as
freestanding or in a stack. Remember that
the tumble dryer produces heat and should
therefore not be located in a room that is
too small. If the room is very small, drying
will take longer due to the limited quantity of
air.
How to fit the stacker
1. Undo the two screws indicated on the
back of the washing machine.
Caution!
The machine must not be installed behind a
lockable door, a sliding door or a door with
hinges on the opposite side to those of the
tumble dryer.
2. Secure the anti-tilt device using the
screws as shown in the picture.
Advice!
To improve ventilation, leave the door to
the room where the tumble dryer is located
open.
Caution!
Any electrical installation must be carried
out by qualified professionals.
3. Attach the plastic cups that will hold the
tumble dryer’s front feet to the washing ma-
chine’s top cover.This is essential, as once
the tumble dryer’s feet are resting in the
plastic cups you know the dryer is correctly
positioned on the washing machine.
A. Freestanding
The tumble dryer can be positioned beside
the washing machine.
B. Stacking
The tumble dryer can be placed on top of
an Asko washing machine. In this case you
use the stacking attachments that come
with the machine:
2 foot cups.These can be found in a bag in
the drum.
2 anti-tilt devices.These come attached to
the bottom left corner on the back of the
machine.
Extending plates can be ordered from your
local retailer.
18
Break off tag A on the cup fitted on the right
side and tag B on the cup fitted on the left
side.Then remove the paper from the self-
adhesive surface under the plastic cups.
Adjusting the feet
Screw the feet in or out so that the tumble
dryer is steady and balanced on the floor or
on the washing machine.Then tighten the
locking nuts.
A
B
Locking nut
4. Fit the plastic cups so that the “tags”
marked with arrows are against the front
edge of the cover and side edge and press
firmly onto the cover.Then break off the
remaining tags.
Condensed water
The machine is supplied as shown in
Option 1 (inset).This means that the
condensed water is pumped into the con-
densed water container.This must then be
removed and emptied by hand.
Option 2 allows you to remove the small
short hose from the blue nipple.Then at-
tach the enclosed rubber hose to the blue
nipple.The water can then be pumped out
into a laundry sink or a floor drain (2a).
5. Push the tumble dryer in under the metal
angles, keeping the front edge raised 1 - 2 cm.
2
1
6. Lower the tumble dryer’s front feet into
the plastic cups and adjust so that the dryer
is balanced.
2a
19
Electrical installation
The machine must only be connected to an
earthed wall socket.
Connection on delivery
The machine is supplied as single-phase,
230V, heat output 2500W (see type plate)
and has a 16A fuse. Any earth fault fuses
must be type A.
Alternative connection
It is possible to switch over from 16A (heat
output 2500) to 10A (heat output 1950W).
Switching must be carried out as follows:
1. Shut off the power.
2. Press and hold the Start/Stop button, and
switch on the power.
3. Release the Start/Stop button once the
programme indicator lights up.
4. Press the Start/Stop button 5 times
(within 10 seconds).
5. Adjust the programme selector so that
the Extra Dry light comes on (10 o’clock).
6. Press the Start/Stop button to store the
setting.
If you want to reset the machine to a 16A
connection:
1. Repeat steps 1-4.
2. In step 5, adjust the programme selector
so that the Extra Dry light goes out.
3. Press the Start/Stop button to store the
setting.
The machine now has a 16A connection.
20
Door hanging
The tumble dryer comes with the door hung
on the left. However, it is possible to change
the door to right hung.
5. Next you must move the plastic plugs on
the upper and lower edges of the door. Use
a flat screwdriver.
Proceed as follows:
1. Remove the lower front plate and undo
the three screws holding the hinge attach-
ment.
6. Unscrew the two screws on the sides of
the door, around five millimetres, to allow
the door magnet and cover washer on the
inside of the door to be removed.
2. Angle the lower edge of the door out to
the left while turning the hinge attachment
as indicated by the arrows.
7.Then remove the door magnet (1) and
cover washer (2).
1
2
Hinge attachment
3. Move the hinge pin. For right hanging,
the hinge attachment must then be turned
upside down.
Hinge pin
8. Insert the door magnet in place of the
cover washer.
4.Then move the hinge pin in the panel’s
lower edge.
21
13. Secure the hinge attachment using the
screws in the sequence shown in the pic-
ture.
9. Insert the cover washer in place of the
door magnet.
10. Insert the screws so that the door mag-
net and cover washer are held in place.
11. Remove the screw indicated. If using a
condenser dryer, you must also open the
condenser panel.
14. Replace the screw unfastened in
point 11.
1
15. Replace the lower front plate.
12.Then fit the door securely on the right
side of the machine.
2
2
2
2
1
22
Search words
A
S
Anti-crease
7, 9
Safety
Service
Sort
4
17
4
C
Care
Child safety
Cleaning
Condensed water container
Condenser
Cotton
Spinning
8
10, 13
5
T
10, 13, 14
4, 6, 10, 11, 13
Technical information
Temperature
Troubleshooting
16
7, 9
15
6, 14
8
D
W
Display
7, 10
4
Wool
8
Disposal
Door hanging
Do not tumble-dry
21
3, 8
E
Electrical installation
Error messages
4, 18, 20
15
F
Felting
Fluff filter
8
6, 13
I
Installation
18, 20
3, 8
L
Laundry labels
O
Options
Overheating cut-out
7, 9
4, 10, 15
P
Packaging
Programmes
4
7, 9
Q
Quick guide
24
23
Quick guide
Fabrics
• Sort fabrics of
1the same kind to
ensure as uni-
form drying as
possible.
Press the Start/Stop button
Drying programme finished
5
• The text
in the display indicates
6that the programme has finished.
• Clean the fluff filter after each load.
• Empty the condensed water con-
tainer.
Press the main power switch
Load the laundry
• Close the door.
Once tumble-drying has
finished
7• Switch off the main power switch,
and close the door.
Select a programme and any
options
4• Turn the Programme selector to the
required programme.
Dry
Normal dry
Extra dry
Iron dry
Air fluff
60 min
Timed dry
60 min
• Select any options and settings.
Item No.: 80 799 89. Rev. 01 We reserve the right to make changes.
Printed on environmentally-friendly paper that meets the demands of the Swedish environmental organisations Miljöförbundet and
Naturskyddsföreningen.
24
|