Handheld Steam Cleaner
MODEL MC1226
Owner’s Guide
Please read all instructions before use.
KEEP YOUR RECEIPT FOR WARRANTY PURPOSES.
10. Do not use unit where aerosol-based products are being used, or where oxygen is being
administered.
11. Unit is only meant to be used with recommended Handheld Steam Cleaner (model MC1226)
accessories. Using other types of attachments may cause damage to unit or injury.
12. If Heating Indicator Light does not illuminate when power cord is plugged in, unit is not
operating normally. Immediately disconnect cord from power supply, then refer to
troubleshooting guide on Page 12 of this manual for assistance.
13. Do not attempt to use unit without properly filling Boiler with water.
14. When filling unit, only water should be used – other cleaning agents could damage unit or
cause injury. Distilled or de-mineralized water is highly recommended, in order to minimize
potential build-up of mineral deposits.
15. To reduce risk of contact with hot water emitting from Steam Aperture, check appliance before
each use by positioning it away from body and turning it on. Do not operate unit if Steam
Aperture is blocked.
16. Burns can occur from touching hot metal parts, hot water, or steam. Do not touch Steam
Aperture or attempt to connect any accessories while unit is in use. Use caution when you
turn unit upside-down – there may be hot water inside.
17. When steaming any surface for the first time, it is recommended that you consult the
manufacturer’s guidelines for the material being steamed. For items in question, test on an
inconspicuous area before proceeding.
18. Do not allow power cord to touch hot surfaces during use. Loosely bundle cord when storing.
19. Always allow Handheld Steam Cleaner to cool (at least 30 minutes for complete cooling) and
empty Boiler before storing.
SAVE THESE INSTRUCTIONS!
FOR HOUSEHOLD USE ONLY
Questions or comments?
1-800-711-6617
•
•
•
Speak your mind! We invite you to review this product online:
|
ENGLISH
3
Product Information
The following features and accessories are included with your Handheld Steam Cleaner.
Carefully inspect the packing material for all parts listed below. To obtain possible missing parts,
refer to Product Support on Page 14 of this manual for Consumer Service contact information.
UNIT FEATURES
& ACCESSORIES
Steam Aperture
Boiler Cap
Steam Button
Handle
Heating Indicator Light
Boiler (internal)
Jet Nozzle
1
2
3
4
5
6
7
8A Short Nylon Utility Brush
8b Long Nylon Utility Brush
8C Brass Utility Brush
9
Wide Nozzle
10 Cloth Cover
11 Squeegee
12 Measuring Cup
|
4
ENGLISH
The Steam Aperture (1) emits a flow of hot, penetrating steam whenever the Steam Button is
pressed and held. Either the Jet Nozzle or Wide Nozzle should always be connected to the
Steam Aperture when the unit is in use.
•
The Boiler Cap (2) is designed to safely contain steam inside the Boiler. The Boiler Cap must
be unscrewed and removed in order to fill the Boiler with water.
The Steam Button (3) is pressed and held in order to start the flow of steam from the Steam
Nozzle, then released when you wish to stop.
•
•
The Handle (4) is engineered to stay cool while providing maximum grip and comfort.
The Heating Indicator Light (5) illuminates when the power cord is plugged in and the Boiler has
begun heating. The Heating Indicator Light will turn off when the Boiler is fully heated and the
unit is ready to begin producing steam.
•
•
The Boiler (6) is the internal reservoir where water is held and heated into steam. For optimal
steam production, the Boiler should be filled with no more than 6 oz. (180 ml.) of water.
The Jet Nozzle (7) connects to the Steam Aperture and is designed to focus the flow of steam
for concentrated cleaning. The Nylon Utility Brushes and Brass Utility Brush all connect to the
Jet Nozzle.
•
•
The Short Nylon Utility Brush (8a), Long Nylon Utility Brush (8b) and Brass Utility Brush (8c) all
connect to the Jet Nozzle and are designed for scrubbing especially tough stains. The Nylon
Utility Brushes are ideal for use on many surfaces around the home, including carpet, ceramic
tile, grouting, and more. The Brass Utility Brush is perfect for use on BBQ grills, oven racks,
automobile engines, shop tools and other hard metal surfaces.
•
NOTE: Some delicate surfaces, such as painted wood or stainless steel, may be scratched
or damaged by the bristles of the Utility Brushes – especially the Brass Utility Brush.
Use careful judgement when deciding what surface to clean with any of the Utility Brushes.
If you are unsure if a surface will be damaged, it is recommended that you test a small
inconspicuous spot before proceeding.
The Wide Nozzle (9) connects to the Steam Aperture, dispersing the flow of steam over a wider
area for more gentle cleaning. The Squeegee and Cloth Cover both connect to the Wide Nozzle.
The Cloth Cover (10) stretches over the Wide Nozzle and is designed to absorb excess moisture,
helping to prevent water spotting. This allows effective steaming of fabrics and upholstery.
The Squeegee (11) connects to the Wide Nozzle and is designed for cleaning windows, mirrors,
and other smooth surfaces.
•
•
•
•
The Measuring Cup (12) provides an easy and convenient way to consistently fill the Boiler with
the optimum amount of water (6 oz. / 180 ml.).
|
ENGLISH
5
Assembling Your
Handheld Steam Cleaner
CONNECTING JET NOZZLE / WIDE NOZZLE
WARNING: DO NOT attempt to connect any accessories while unit is emitting steam.
Doing so could result in burns or other injury.
1. Insert cylinder on back of Jet Nozzle or Wide Nozzle (FIGURE 1-A) into opening of Steam
Aperture (FIGURE 1-B). Align it so that two tabs on sides of cylinder fit into two guide grooves
on sides of opening, as indicated in FIGURE 1. Be sure to push accessory in as far as possible.
TABS
GUIDE GROOVES
1-A
1-B
FIGURE 1
2. Rotate Jet Nozzle or Wide Nozzle in a clockwise direction as indicated (FIGURE 2-A). Twist
until you feel it “lock” into place and it will move no further. Note that single guide line above
Steam Aperture aligns between dual guide lines on Jet Nozzle / Wide Nozzle (FIGURE 2-B).
2-A
2-B
FIGURE 2
3. Note the color difference between the Jet Nozzle or Wide Nozzle (gray) and the Steam Aperture
(yellow). When removing the Jet Nozzle or Wide Nozzle, be sure you are only trying to rotate
and remove the gray accessory. The Steam Aperture will not rotate and cannot be removed.
|
6
ENGLISH
CONNECTING UTILITY BRUSHES
NOTE: Both Nylon Utility Brushes and the Brass Utility Brush are all attached in the same
manner.
1. Begin by aligning hexagonal-shaped hole on back of Utility Brush (FIGURE 3-A) with hexagonal
tip of Jet Nozzle (FIGURE 3-B).
2. Firmly press Utility Brush onto tip of Jet Nozzle (FIGURE 3-C).
CAUTION: Make sure Utility Brush is pushed as far as possible onto tip to ensure that it
is seated securely. This will prevent steam leaks and ensure that Utility Brush is not
forced off of Jet Nozzle by steam pressure.
3. To remove Utility Brush, simply grasp and firmly pull until it disconnects from Jet Nozzle.
CAUTION: Make sure unit is unplugged and has had sufficient time to cool down before
attempting to remove any accessories.
3-A
3-B
3-C
FIGURE 3
|
ENGLISH
7
Assembling Your
Handheld Steam Cleaner
CONNECTING SQUEEGEE
1. Connect Squeegee to Wide Nozzle by inserting
hook tabs on Squeegee (FIGURE 4-A) into
slots on Wide Nozzle (FIGURE 4-B).
2. Swing Squeegee backwards until hook latch on
back snaps over tab on top of Wide Nozzle.
3. Connect Wide Nozzle to Steam Aperture as normal
(refer to Page 6 for details).
4-A
4-B
USING CLOTH COVER
FIGURE 4
1. Simply stretch Cloth Cover around Wide Nozzle
(FIGURE 5). Cloth Cover should fit snugly
enough to stay in place while steaming.
2. Connect Wide Nozzle to Steam Aperture as
normal (refer to Page 6 for details).
FIGURE 5
|
8
ENGLISH
Using Your
Handheld Steam Cleaner
FILLING BOILER
1. Place Handheld Steam Cleaner on a flat, level surface.
2. Make sure power cord is unplugged from electrical outlet.
3. Cautiously remove Boiler Cap by unscrewing it in a counter-clockwise direction, and lift it off.
CAUTION: Refer to Refilling procedure below for additional safety precautions that must
be taken when refilling the unit after it has been in use.
4. Boiler should always be emptied after each use. If it was not emptied after the previous use,
empty it now – this will make it easier to fill with the correct amount of water.
5. Fill included Measuring Cup with 6 oz. (180 ml.) of water.
NOTE: In order to extend the life of your Handheld Steam Cleaner and keep it functioning
at it’s maximum potential, it is highly recommended that distilled or de-mineralized
water be used in Boiler.
6. Carefully pour water from Measuring Cup into Boiler through fill hole.
NOTE: Do not exceed the Boiler’s maximum capacity of 6 oz. (180 ml.). This will ensure
a better flow of steam with minimal dripping water.
7. Replace Boiler Cap, screwing it in a clockwise direction to tighten. Make sure it is screwed on
securely to prevent hot water or steam from escaping.
REFILLING
If unit has been in use, always use the following safety precautions before removing
the Boiler cap to add water:
1. Unplug power cord from electrical outlet.
2. Allow 5-10 minutes for Boiler to cool.
3. Press and hold Steam Button to release any remaining steam pressure. Steam can remain
pressurized inside Boiler for up to one hour after use.
4. Slowly remove Boiler Cap and add water as outlined in Steps 3-7 of Filling with Water
procedure above.
CAUTION: Boiler may contain some amount of water that is still hot – use care when
refilling to avoid burns or other injury.
WARNING: Extreme caution should be used when pouring water into a Boiler that was
recently heated – cool water introduced into a warm Boiler may result in a small burst of
steam and water. Do not look directly down into fill hole when filling. Keep your free
hand and any children or pets at a safe distance.
|
ENGLISH
9
Using Your
Handheld Steam Cleaner
STEAM CLEANING
NOTE: Before operating, make sure all desired accessories are connected and Boiler is
filled with the correct amount of water (refer to Pages 6-9 for details).
1. For first-time use, remove protective plastic cover that is shipped on electrical plug. Plug
power cord into a convenient 3-prong electrical outlet. Heating Indicator Light will illuminate to
show that unit is receiving power and Boiler has begun to heat.
CAUTION: This unit uses a grounded (3-prong) electrical plug. Use only in properly
installed 3-prong electrical outlets. Do not attempt to alter plug or circumvent this
safety feature in any way.
2. After approximately 3 minutes, Heating Indicator Light will turn off. This indicates that Boiler is
fully heated, and unit is ready to begin steaming.
NOTE: Heating Indicator Light may cycle off and on during use, accompanied by a slight
temporary drop in steam pressure – this is a normal part of operation, as the Boiler
works to maintain a steady optimal temperature.
3. Point Steam Aperture (and any connected accessories) towards surface you wish to steam,
and press Steam Button. Hold Button down for a continuous flow of steam.
CAUTION: Always be sure that Steam Aperture and other accessories are pointed in a
safe direction (away from yourself, other people, pets, and plants) before pressing
Steam Button.
NOTE: When steaming any surface for the first time, it is recommended that you consult
the manufacturer’s guidelines for material being steamed. For items in question, test
steam on an inconspicuous area before proceeding.
4. Using a slight back-and-forth motion over the area you are steaming will enhance the cleaning
process, as will scrubbing the area (if a Utility Brush is connected). Wipe steamed areas with a
clean cloth to remove loosened dirt and grime.
CAUTION: Wiping an area while it is still wet is recommended, but use care when wiping
surfaces such as metal that may still be hot.
5. To effectively kill bacteria and other microorganisms, hold Steam Aperture (and any connected
accessories) approximately 1/2 inch from surface and press Steam Button. Keep Steam
Button held and concentrate steam on the same spot for at least 5 seconds.
6. At its maximum capacity (6 oz. / 180 ml.), the Boiler will provide approximately 8 minutes of
continuous steam. If you wish to continue steaming, refer to Refilling procedure on Page 10
to refill Boiler.
7. Once you are finished using your Handheld Steam Cleaner, immediately unplug power cord
from electrical outlet. Refer to Storage & Care guidelines on Page 11 for proper cleaning and
storage procedures.
|
10 ENGLISH
Storage & Care
PROPER STORAGE
Preparing your Handheld Steam Cleaner for storage is quick and simple. When you have finished
your steaming tasks, follow the steps listed below.
1. Unplug power cord from electrical outlet.
2. Allow unit to cool (at least 30 minutes for complete cooling).
3. Press and hold Steam Button to release any remaining steam pressure.
4. Remove any connected accessories from unit.
5. Unscrew and remove Boiler Cap. Drain any remaining water in Boiler into a sink or tub – this
will help to minimize potential mineral build-up in the Boiler, as well as prevent unintentional
overfilling during your next use.
5. Loosely replace Boiler Cap. Do not screw on tightly, as this may make it difficult to remove in
the future.
6. Loosely bundle power cord and store Handheld Steam Cleaner and all accessories in a cool,
dry location.
MINERAL BUILD-UP
A common maintenance need for steam appliances is the removal of build-up caused by high
mineral content in many municipal water supplies. This mineral build-up may limit the
effectiveness and reduce the life of your Handheld Steam Cleaner.
The best way to minimize mineral build-up is to use distilled or de-mineralized water when
using your Handheld Steam Cleaner. In addition, it is recommended that the unit be cleaned at
least once a month in order to remove any deposits that form. This will help to extend the life of
your Handheld Steam Cleaner and keep it functioning at its maximum potential.
To remove mineral build-up:
1. Unplug power cord from electrical outlet.
NOTE: Unit should remain unplugged for duration of cleaning procedure.
2. Allow unit to cool (at least 30 minutes for complete cooling).
3. Press and hold Steam Button to release any remaining steam pressure.
4. Remove any connected accessories from unit.
5. Unscrew and remove Boiler Cap. Drain any remaining water in Boiler into a sink or tub.
6. Fill Measuring Cup with 6 oz. (180 ml.) vinegar.
7. Carefully pour vinegar into Boiler through fill hole.
8. Slowly shake or move unit around to agitate vinegar.
9. Allow vinegar to soak in Boiler for at least 40 minutes, or more if possible.
10. Drain vinegar out of Boiler into a sink or tub.
11. Thoroughly rinse Boiler with fresh water, drain and repeat until vinegar odor dissipates.
12. Loosely replace Boiler Cap and follow normal storage procedure as outlined in Proper
Storage section above.
|
ENGLISH 11
Troubleshooting
PROBLEM
POSSIBLE CAUSE
Unit is not plugged in.
SOLUTION
Unit fails to heat up and begin
steaming. Heating Indicator Light
DOES NOT illuminate.
Plug power cord into electrical outlet.
Household circuit breaker / ground
fault interrupter has tripped or blown interrupter, or replace fuse. For
Reset circuit breaker / ground fault
a fuse.
assistance, contact a licensed electrician.
Unit is damaged or otherwise in
need of repair.
Immediately cease usage and unplug.
Contact Consumer Service for
assistance (see Page 13 for details).
Unit fails to heat up and begin
steaming. Heating Indicator Light
DOES illuminate.
No water in Boiler.
Refer to Filling With Water procedure
on Page 9 to fill unit with water.
Mineral build-up in unit.
Refer to Mineral Build-up section on
NOTE: Always allow sufficient
time for unit to heat up and begin
producing steam.
Page 11 for cleaning procedure.
Unit is damaged or otherwise in
need of repair.
Immediately cease usage and unplug.
Contact Consumer Service for
assistance (see Page 13 for details).
Steam output is weak or intermittent. Water level in Boiler is running low.
Mineral build-up in unit.
Refer to Filling With Water procedure
on Page 9 to refill unit with water.
Refer to Mineral Build-up section on
Page 11 for cleaning procedure.
Boiler Cap cannot be unscrewed.
Boiler Cap has been overtightened
after previous use.
Boiler Cap should always be replaced
loosely when storing. For assistance
with a Cap that has become stuck,
contact Consumer Service (see Page
13 for details).
Jet Nozzle / Wide Nozzle cannot be
removed.
Attempting to disconnect accessory
at the wrong point.
Check to be certain that you are
attempting to remove the accessory
only (gray), and not the Steam
Aperture as well (yellow).
|
12 ENGLISH
Product Support
CONSUMER SERVICES
For problems with your Handheld Steam Cleaner, please refer to the troubleshooting guide located
on Page 12 of this manual. Additional inquiries should be directed to our consumer support services
If you do not have internet access, you may also contact our Consumer Service Department by
telephone, at 1-800-711-6617.
NOTE: In order for our Consumer Service representatives to help you as quickly and
efficiently as possible, please have the following information ready before calling:
• Purchase information (where and when you purchased this product)
• Copy of purchase receipt / proof of purchase
• Product serial number (located on electrical specification label on bottom of unit)
• Date code (4-digit number located on electrical specification label)
For information regarding your 1 year limited warranty, refer to Page 15 of this manual.
PRODUCT SPECIFICATIONS
MC1226
MODEL
120V
VOLTAGE
900W
WATTAGE
7.5A
AMPERAGE
6 OZ. (180 ML.)
WATER CAPACITY
HEATING TIME
3 MIN. (APPROXIMATE)
8 MIN. (APPROXIMATE)
2.8 LBS. (1.3 KG.)
CONTINUOUS STEAM TIME
UNIT WEIGHT
14.6” (37.0 CM.) x 5.9” (15.0 CM.) x 8.4” (21.3 CM.)
12.5’ (380.0 CM.)
UNIT DIMENSIONS
POWER CORD LENGTH
|
ENGLISH 13
Product Support
REPLACEMENT ACCESSORIES
When ordering accessories for your Handheld Steam Cleaner, you may refer to the part numbers
below. Replacement accessories may be ordered through our Web site:
You may also contact Consumer Service directly:
SHORT UTILITY BRUSH
A220-002R-
JET NOZZLE
A220-000R-
LONG UTILITY BRUSH
A220-003R-
BRASS UTILITY BRUSH
A220-004R-
WIDE NOZZLE
A220-100R-
CLOTH COVER
A220-006R-
SQUEEGEE
A220-011R-
MEASURING CUP
A220-008R-
NOTE: Due to continuing improvements, part numbers listed above may change.
For assistance ordering parts, please contact Consumer Service directly.
|
14 ENGLISH
Warranty Information
1 YEAR LIMITED WARRANTY
Steamfast, a division of Vornado Air LLC, (“Steamfast”) warrants to the original consumer or purchaser
this McCulloch Handheld Steam Cleaner SF-226 (“Product”) is free from defects in material or
workmanship for a period of one (1) year from the date of purchase. If any such defect is discovered
within the warranty period, Vornado, at its discretion, will repair or replace the Product at no cost if the
Product is returned to Steamfast postage-paid. Repairs not covered by the warranty or outside the
warranty period will require a fee to cover the cost of materials, handling and shipping.
This warranty does not apply to defects resulting from abuse of the Product, modification, alteration,
repair or service of the Product by anyone other than Steamfast, mishandling, improper maintenance,
commercial use of the Product, damages which occur in shipment or are attributed to acts of God.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE
REMEDY OF THE CONSUMER. STEAMFAST SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS
PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BYAPPLICABLE LAW, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS
LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow
limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may have other rights that vary from state to state.
For warranty or repair service, call 1-800-711-6617 or email [email protected] to obtain
a Return Authorization (“RA”) form. Please have or include your Product’s model number, date code and
serial number, as well as your name, address, city, state, zip code and phone number when contacting
Steamfast for warranty service. You may be required to provide the original sales receipt. For your
records: Staple or attach your original sales receipt to this Owner’s Guide. Please also write your
Product’s serial number below (located on product specs decal).
Serial No. __________________________________________________________________________
After receiving the RA form, ship your Product to:
Steamfast
Attn: Warranty & Repair
415 East 13th
Andover, KS 67002
To assure proper handling, packages must be clearly marked with the RA number. Packages not
clearly marked with the RA number may be refused at the receiving dock.
Please allow 1-2 weeks for repair and return of your Product after the Product is received.
© 2011 Vornado Air LLC • Andover, KS 67002
Specifications subject to change without notice.
Steamfast® is a trademark owned by Vornado Air LLC.
Manufactured in China.
Steamfast Consumer Service
|
P: 1-800-711-6617
|
|
ENGLISH 15
review this product online
Steamfast
415 East 13th, Andover, KS 67002
V110302
|