INSTRUCTION MANUAL
IMPORTANT INFORMATION: Please read these instructions carefully
and make sure you understand them before using this unit. Retain these
instructions for future reference.
GB
ES
MANUAL DE INSTRUCCIONES
INFORMACIÓN IMPORTANTE: Lea atentamente las instrucciones y
asegúrese de entenderlas antes de utilizar esta aparato. Conserve las
instrucciones para la referencia en el futuro.
MANUEL D’INSTRUCTIONS
RENSEIGNEMENTS IMPORTANTS: Avant d’utiliser cet appareil,
veuillez lire atentivement les instructions et assurez--vous de les avoir
comprises. Conservez les instructions pour référence ultérieure.
FR
PT
RU
MANUAL DO OPERADOR
INFORMAÇÕES IMPORTANTES: Queira ler cuidadosamente estas
instruções e tenha certeza de entendë--las antes de usar a serra e
guarde para consulta futura.
545154793 Rev. 3 11/4/08 BRW
IDENTIFICATION OF SYMBOLS
Starting Reminder
Move ON/STOP switch to
the ON position.
Pull the starter rope
sharply 5 times with your
right hand.
Push the choke/fast idle
lever in to the HALF
CHOKE position.
Slowly press primer bulb
6 times.
Pull choke/fast idle lever
out to the full extent (to
the FULL CHOKE posi-
tion).
Pull the starter rope sharply
with your right hand until
the engine starts.
SAFETY RULES
S Always use approved hearing protection.
Regular users should have hearing
checked regularly as chain saw noise can
damage hearing. Long--term exposure to
noise can result in permanent hearing im-
pairment.
WARNING: Always disconnect
spark plug wire and place wire where it can-
not contact spark plug to prevent accidental
starting when setting up, transporting, ad-
justing or making repairs except carburetor
adjustments.
Because a chain saw is a high-speed wood-
cutting tool, special safety precautions must
be observed to reduce the risk of accidents.
Careless or improper use of this tool can
cause serious injury.
S Keep all parts of your body away from the
chain when the engine is running.
S Keep children, bystanders, and animals a
minimum of 10 Meters away from the work
area. Do not allow other people or animals
to be near the chain saw when starting or
operating the chain saw.
S Do not handle or operate a chain saw when
you are fatigued, ill, or upset, or if you have
taken alcohol, drugs, or medication. You
must be in good physical condition and men-
tally alert. Chain saw work is strenuous. If
you have any condition that might be aggra-
vated by strenuous work, check with your
doctor before operating a chain saw.
PLAN AHEAD
S Read this manual carefully until you com-
pletely understand and can follow all safety
rules, precautions, and operating instruc-
tions before attempting to use the unit.
S Restrict the use of your saw to adult users
who understand and can follow safety
rules, precautions, and operating instruc-
tions found in this manual.
S Carefully plan your sawingoperation inad-
vance. Do not start cutting until you havea
clear work area, secure footing, and, if you
are felling trees, a planned retreat path.
Hearing
Safety Hat
Protection
e
tection
Snug
OPERATE YOUR SAW SAFELY
Fitting
Clothing
avy Duty
oves
WARNING: Long term inhalation of
the engine’s exhaust fumes, chain oil mist and
dust from sawdust can result in serious per-
sonal injury.
S Do not operate a chain saw with one hand.
Serious injury to the operator, helpers, by-
standers or any combination of these per-
sons may result from one-handed opera-
tion. A chain saw is intended for two-
handed use.
S Operate the chain saw only in a well-venti-
lated outdoor area.
S Do not operate saw from a ladder or in a
tree, unless you are specifically trained to
do so.
Safety
Shoe
Chaps
S Wear protective gear. Always use steel-toed
safety footwear with non-slip soles; snug-fit-
ting clothing; heavy-duty, non-slip gloves;
eye protection such as non-fogging, vented
goggles or face screen; an approved safety
hard hat; and sound barriers (ear plugs or
mufflers) to protect your hearing. Secure hair
above shoulder length.
3
S Make sure the chain will not make contact
with any object while starting the engine.
Never try to start the saw when the guide
bar is in a cut.
S Do not put pressure on the saw at the end of
the cut. Applying pressure can cause you to
lose control when the cut is completed and
may cause serious personal injury.
S Stop the engine before setting the saw
down.
ance of these problems. Users who operate
power tools on a continual and regular basis
must monitor closely their physical condition
and the condition of this tool.
S ON/STOP switch. The ON/STOP switch
should be used to stop the engine.
CHECKING, MAINTAINING AND
SERVICING CHAIN SAW SAFETY
EQUIPMENT
S Do not operate a chain saw that is dam-
aged, improperly adjusted, or not com-
pletely and securely assembled. Always
replace bar, chain, hand guard, or chain
brake immediately if it becomes damaged,
broken or is otherwise removed.
S With the engine stopped, hand carry the
chain saw with the muffler away from your
body, and the guide bar and chain to the
rear, preferably covered with a scabbard.
WARNING: Never use a chain saw
with defective safety equipment. Safety
equipment must be inspected and main-
tained. If your chain saw does not pass in-
spection, take the saw to your nearest ser-
vice dealer for repair.
S Chain brake. Brush off any wood dust,
resin and dirt from the chain brake and
clutch drum. Dirt and wear can impair op-
eration of the brake. For additional infor-
mation, see OPERATING YOUR UNIT
section.
CHAIN SAW SAFETY EQUIPMENT
NOTE: In this section, the safety features of
the chain saw and their function are explained.
For inspection and maintenance, see instruc-
tions in the CHECKING, MAINTAINING AND
SERVICING CHAIN SAW SAFETY EQUIP-
MENT section. See instructions under the
WHAT IS WHAT? section, to find where these
parts are located on your chain saw. The life
span of the machine can be reduced and the
risk of accidents can increase if machine
maintenance is not carried out correctly and
if service and/or repairs are not carried out
professionally. If you need further informa-
tion, please contact your nearest service
dealer.
S Throttle trigger lock -out. Check that the
throttle trigger can not beoperated until the
throttle lock--out is pressed.
S Chain catcher. Check that the chain
catcher is not damaged and is firmly at-
tached to the body of the chain saw.
S Vibration damping system. Regularly
check the vibration damping units for
cracks or deformation. Make sure the
vibration damping units are securely at-
tached to the engine unit and handle unit.
S ON/STOP switch. Start the engine and
make sure the engine stops when you
move the ON/STOP switch to the STOP
position.
S Chain brake. Your chain saw is equipped
with a chain brake that is designed to stop
the chain from moving.
MAINTAIN YOUR SAW IN GOOD
WORKING ORDER
S Have all chain saw service performed by a
qualified service dealer with the exception of
the items listed in the maintenance section of
this manual. For example, if improper tools
are used to remove or hold the flywheel
when servicing the clutch, structural damage
to the flywheel can occur and cause the fly-
wheel to burst.
WARNING: The chain brake is de-
signed to stop the chain immediately if you
get a kickback. The chain brake reduces the
risk of accidents, but only you can prevent
them. DO NOT ASSUMETHAT THE CHAIN
BRAKE WILL PROTECT YOU IN THE
EVENT OF A KICKBACK.
S Throttle trigger lock -out. The throttle
lock--out is designed to prevent accidental
operation of the throttle trigger.
S Chain catcher. The chain catcher is de-
signed to catch the saw chain if it breaks.
S Vibration damping system. Your chain
saw is equipped with a vibration damping
system that is designed to minimize vibra-
tion and make operation easier.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of peo-
ple prone to circulation disorders or abnormal
swellings. Prolonged use in cold weather has
been linked to blood vessel damage in other-
wise healthy people. If symptoms occur such
as numbness, pain, loss of strength, change in
skin color or texture, or loss of feeling in the fin-
gers, hands, or joints, discontinue the use of
this tool and seek medical attention. An anti-
vibration system does not guarantee the avoid-
S Make certain the saw chain stops moving
when the throttle trigger is released. For
correction, refer to CARBURETOR AD-
JUSTMENTS.
S Never modify your saw in any way. Use
only attachments supplied or specifically
recommended by the manufacturer.
S Keep the handles dry, clean, and free of oil
or fuel mixture.
S Keep fuel and oil caps, screws, and fas-
teners securely tightened.
S Use only McCulloch accessories and re-
placement parts as recommended.
HANDLE FUEL WITH CAUTION
S Do not smoke while handling fuel or while
operating the saw.
S Eliminate all sources of sparks or flame in
the areas where fuel is mixed or poured.
There should be nosmoking, openflames,
or work that could cause sparks. Allow en-
gine to cool before refueling.
4
S Mix and pour fuel in an outdoor area on bare
ground; store fuel in a cool, dry, well venti-
lated place; and use an approved, marked
container for all fuel purposes. Wipe up all
fuel spills before starting saw.
S Move at least 10 feet (3 meters) from fuel-
ing site before starting engine.
Obstructions
Clear
Working Area
S Turn the engine off and let saw cool in a
non-combustible area, not on dry leaves,
straw, paper, etc. Slowly remove fuel cap
and refuel unit.
S Storetheunit and fuel in an area where fuel
vapors cannot reach sparks or open
flames from water heaters, electric motors
or switches, furnaces, etc.
REDUCE THE CHANCE OF
KICKBACK
S Recognize that kickback can happen.
With a basic understanding of kickback,
you can reduce the element of surprise
which contributes to accidents.
S Never let themoving chain contact any ob-
ject at the tip of the guide bar.
KICKBACK
S Keep the working area free from obstruc-
tions such as other trees, branches, rocks,
fences, stumps, etc. Eliminate or avoid any
obstruction that your saw chain could hit
while you are cutting through a particular log
or branch.
WARNING: Avoid kickback which
can result in serious injury. Kickback is the
backward, upwardor sudden forwardmotion
of the guide bar occurring when the saw
chain near the upper tip of theguide bar con-
tacts any object such as a log or branch, or
when the wood closes in and pinches the
saw chain in the cut. Contacting a foreignob-
ject in the wood can also result in loss of
chain saw control.
S Rotational Kickback can occur when the
moving chain contacts an object at the up-
per tip of the guide bar. This contact can
cause the chain to dig into the object,
which stops the chain for an instant. The
result is a lightning fast, reverse reaction
which kicks the guide bar up and back to-
ward the operator.
S Pinch-Kickback can occur when the the
wood closes in and pinches the moving
saw chain in the cut along the top of the
guide bar and the saw chain is suddenly
stopped. This sudden stopping of the
chain results in a reversal of the chain
force used to cut wood and causes the
saw to move in the opposite direction of the
chain rotation. The saw is driven straight
back toward the operator.
S Keep your saw chain sharp and properly
tensioned. A loose or dull chain can increase
the chance of kickback occurring. Follow
manufacturer’s chain sharpening and main-
tenance instructions. Check tension at regu-
lar intervals with the engine stopped, never
with the engine running. Make sure the bar
clamp nuts are securely tightened after ten-
sioning the chain.
S Begin and continue cutting at full speed. If
the chain is moving at a slower speed, there
is greater chance of kickback occurring.
S Cut one log at a time.
S Use extreme caution when re-entering a
previous cut.
S Do not attempt cuts starting with the tip of
the bar (plunge cuts).
S Watch for shifting logs or other forces that
could close a cut and pinch or fall into chain.
S Use the Reduced--Kickback Guide Bar
and Low--Kickback Chain specified for
your saw.
MAINTAIN CONTROL
S Pull-In can occur when the moving chain
contacts a foreign object in the wood in the
cut along the bottom of the guide bar and the
saw chain is suddenly stopped. This sudden
stopping pulls the saw forward and away
from the operator and could easily cause the
operator to lose control of the saw.
Stand to the lef
the saw
Avoid Pinch -Kickback:
S Be extremely aware of situations or obstruc-
tions that can cause material to pinch the top
of or otherwise stop the chain.
Never reverse
hand positions
S Do not cut more than one log at a time.
S Do not twist the saw as the bar is with-
drawn from an undercut when bucking.
Avoid Pull -In:
S Always begin cutting with the engine at full
speed and the saw housing against wood.
S Use wedges made of plastic or wood.
Never use metal to hold the cut open.
Elbow locked
Kickback Path
Thumb on underside of
handlebar
5
S Keep a good, firm gripon the saw with both
hands when the engine is running and
don’t let go. A firmgrip will help you reduce
kickback and maintain control of the saw.
Keep the fingers of your left hand encir-
cling and your left thumb under the front
handlebar. Keepyour right handcomplete-
ly around the rear handle whether your are
right handed or left handed. Keep your left
arm straight with the elbow locked.
S Position your left hand on the front handle-
bar so it is in a straight line with your right
hand on the rear handle when making
bucking cuts. Never reverse right and left
hand positions for any type of cutting.
S Standwith your weight evenly balancedon
both feet.
S Stand slightly to the left side of the saw to
keep your body from being in a direct line
with the cutting chain.
S Do not overreach. You could be drawn or
thrown off balance and lose control of the
saw.
S Do not cut above shoulder height. It is diffi-
cult to maintain control of saw above
shoulder height.
KICKBACK SAFETY FEATURES
S Low--Kickback Chain, designed with a
contoured depth gauge and guard link
which deflect kickback force and allow
wood to gradually ride into the cutter.
Low-Kickback Chain
Contoured Depth Gauge
Elongated Guard Link
Deflects Kickback
Force And Allows
Wood To Gradually
Ride Into Cutter
S Handguard, designed to reduce the
chance of your left hand contacting the
chain if your hand slips off the front handle-
bar.
S Position of front and rear handlebars, de-
signed with distance between handles and
“in-line” with each other. The spread and
“in-line” position of the hands provided by
this design work together to give balance
and resistance in controlling the pivot of
the saw back toward the operator if kick-
back occurs.
WARNING: DO NOT RELY UPON
ANY OF THE DEVICES BUILT INTO YOUR
SAW. YOU SHOULD USE THE SAW
PROPERLY AND CAREFULLY TO AVOID
KICKBACK. Reduced--kickback guide bars
and low--kickback saw chains reduce the
chance and magnitude of kickback and are
recommended. Your saw has a low kick-
back chain and bar as original equipment.
Repairs on a chain brake should be made by
an authorized servicing dealer. Take your
unit to the place of purchase if purchased
from a servicing dealer, or to the nearest au-
thorized master service dealer.
S Tip contact in some cases may cause a light-
ning fast reverse REACTION, kicking the
guide bar up and back toward the operator.
S Pinching the saw chain along the top of the
guide bar may push the guide bar rapidly
back toward the operator.
WARNING: The following features are
included on your saw to help reduce the hazard
of kickback; however, such features will not to-
tally eliminate this dangerous reaction. As a
chain saw user, do not rely only on safety de-
vices. You must follow all safety precautions,
instructions, and maintenance in this manual to
help avoid kickback and other forces which
can result in serious injury.
S Reduced--Kickback Guide Bar, designed
with a small radius tip which reduces the
size of the kickback danger zone on the
bar tip. A Reduced--Kickback Guide Bar has
been demonstrated to significantly reduce
the number and seriousness of kickbacks.
Reduced Kickback
Symmetrical Guide
Bar
S Either of these reactions may cause you to
lose control of the saw which could result
in serious injury. Do not rely exclusively
uponthesafety devices built into your saw.
Small Radius Tip
Symm
Large Radius Tip
ASSEMBLY
Protective gloves (not provided) should be
worn during assembly.
3. Attach the bumper spike with the two
screws as illustrated.
ATTACHING THE BUMPER
SPIKE
The bumper spike may be used as a pivot
when making a cut.
1. Lift adjustment knob handle and turn coun-
terclockwise to loosen chain brake.
2. Align arrows by pressing tensioning le-
ver down to install position (see illustra-
tion). Remove chain brake from saw.
6
7. Carefully remove new chain from pack-
age. Prepare the chain by checking the
proper direction. Without following the il-
lustration, it is easy to place the chain on
the saw in the wrong direction. Use the
illustration of the chain to determine the
proper direction.
ATTACHING THE BAR & CHAIN (If
not already attached)
1. Move ON/STOP switch to the STOP
position.
2. Make sure chain brake is disengaged
(see CHAIN BRAKE in theOPERATION
section).
IMPORTANT: Before proceeding to next
step, ensure unit is on a flat surfaceand inan
upright position as shown in illustration be-
low. Chain will not tighten properly if the unit
is not in an upright position.
3. Lift adjustment knob handle and turn coun-
terclockwise to loosen chain brake.
Tip of
Bar
Adjustment
Knob
Handle
CUTTERS MUST FACE IN
DIRECTION OF ROTATION
Depth Gauge
Cutters
Drive Links
8. Place chain over and behind clutch, fitting
the drive links in the clutch drum sprocket.
9. Fit bottom of drive links between the
teeth in the sprocket in the nose of the
guide bar.
10. Fit chain drive links into bar groove.
11. Pull guide bar forward until chain is snug
in guide bar groove. Ensureall drive links
are in the bar groove.
TO REPLACE CHAIN BRAKE:
1. Align arrows on chain brake by pressing
tensioning lever down to install position
(see illustration).
Tensioning Lever
LOOSEN
4. Align arrows by pressing tensioning le-
ver down to install position (see illustra-
tion). Remove chain brake from saw.
2. Install chain brake. Turn adjustment
knob handle clockwise until knob begins
to thread onto bolt.
3. Release tensioning lever. Chain will
tighten automatically.
4. While lifting tip of guide bar, turn adjust-
ment knob handle clockwise to clamp
bar. Tighten until bar is clamped secure-
ly. Hand tighten securely; do not use
tools to tighten!
ING LEVER IN
INSTALL POSITION
5. Remove the plastic shipping spacer (if
present).
6. Slide guide bar behind clutch drum until
guide bar stops against clutch drum
sprocket.
Chain
Brake
Clutch Drum
TIGHTEN
7
5. Return adjustment knob handle to original
position. Ensure teeth of adjustment knob
handle are engaged with notches in the
chain brake and adjustment knob handle
is laying flat.
4. Lift adjustment knob handle and turn
counterclockwise 1 turn to loosen bar.
Chain will tighten automatically.
NOTE: If chain brake detaches from saw,
see TO REPLACE CHAIN BRAKE section.
Adjustment
Knob
Handle
Teeth
Notches
CHAIN TENSION (Including units
with chain already installed)
WARNING: Wear protective gloves
when handling chain. The chain is sharpand
can cut you even when it is not moving.
It is normal for a new chain to stretch during the
first 15 minutes of operation. You should re-
check your chain tension frequently and adjust
the chain tension as required. Always check
chain tension each time you use and refuel
your saw or when any sag in the chain is noted.
1. Move ON/STOP switch to the STOP
position.
2. Make sure chain brake is disengaged
(see CHAIN BRAKE in theOPERATION
section).
IMPORTANT: Before proceeding to next
step, ensure unit is on a flat surfaceand inan
upright position as shown in illustration.
Chain will not tighten properly if the unit is not
in an upright position.
Tensioning Lever
LOOSEN
5. While lifting tip of guide bar, turn adjust-
ment knob handle clockwise to clamp
bar. Tighten until bar is clamped secure-
ly. Hand tighten securely; do not use
tools to tighten!
6. Using chain adjustment tool (bar tool),
roll chain around guide bar to ensure all
links are in bar groove.
7. Return adjustment knob handle to original
position. Ensure teeth of adjustment knob
handle are engaged with notches in the
chain brake and adjustment knob handle
is laying flat.
WARNING: If the saw is operated
with a loose chain, the chain could jump off
the guide bar and result in serious injury.
3. Use the chain adjustment tool (bar tool)
to move chain around guide bar to en-
sure kinks do not exist. The chain should
rotate freely.
WARNING: Muffler is very hot during
and after use. Do not touch the muffler or al-
low combustible material such as dry grass
or fuel to do so.
CHAIN SAW IN UPRIGHT POSITION
Guide
Bar
Chain Adjustment
Adjustment Knob
Tool (Bar Tool)
OPERATING YOUR UNIT
BEFORE STARTING ENGINE
BAR AND CHAIN LUBRICATION
The bar and chain require continuous lubri-
cation. Lubrication is provided by the auto-
matic oiler system when the oil tank is kept
filled. Lack of oil will quickly ruin the bar and
chain. Too little oil will cause overheating
shown by smoke coming from the chain and/
or discoloration of the bar.
WARNING: Be sure to read the fuel
information in the safety rules before you be-
gin. If you donot understand the safety rules,
do not attempt to fuel your unit. Contact an
authorized service dealer.
Only use Bar and Chain Oil for bar and chain
lubrication.
8
Oil C
IMPORTANT POINTS TO REMEMBER
When pulling the starter rope, do not use the full
extent of the rope as this can cause the rope to
break. Do not let starter rope snap back. Hold
the handle and let the rope rewind slowly.
For cold weather starting, start the unit at full
choke; allow the engine to warm up before
squeezing the throttle trigger.
mix cap
FUELING ENGINE
NOTE: Do not cut material with the choke/
WARNING: Remove fuel cap slowly
when refueling.
fast idle lever at the FULL CHOKE position.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
NOTE: In the following steps, when the
choke/fast idle lever is pulled out to the full
extent, the correct throttle setting for starting
is set automatically.
This engine is certified to operate on unleaded
gasoline. Before operation, gasoline must be
mixed with a good quality 2-cycle air-cooled
engine oil designed to be mixed at a ratio of
40:1. A 40:1 ratio is obtained by mixing 0,125
liter of oil with 5 liters of unleaded gasoline. DO
NOT USE automotive or boat oil. These oils
will cause engine damage. When mixing fuel
follow the instructions printed on the container.
Always read and follow the safety rules relating
to fuel before fueling your unit.
ON/STOP SWITCH
(SIDE VIEW)
ON
IMPORTANT
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads
to separation and formation of acids during
storage. Acidic gas can damage the fuelsys-
tem of an engine while in storage. To avoid
engine problems, empty the fuel system be-
fore storage for 30 days or longer. Drain the
gas tank, start the engine and let it run until
the fuel lines and carburetor are empty. Use
fresh fuel next season. Never use engine or
carburetor cleaner products in the fuel tank
or permanent damage may occur.
STOP
1. Move ON/STOP switch to the ON posi-
tion.
2. Slowly press primer bulb 6 times.
3. Pull out choke/fast idle to the full extent
(to the FULL CHOKE position).
4. Pull the starter rope sharply 5 times with
your right hand. Then, proceed to the
next step.
NOTE: If the engine sounds as if it is trying
to start before the 5th pull, stop pulling and
immediately proceed to the next step.
5. Push the choke/fast idle lever in to the
HALF CHOKE position.
CHAIN BRAKE
Ensure chain brake is disengaged by pulling
the front hand guard back toward the front han-
dle as far as possible. The chain brake must
be disengaged before cutting with the saw.
CHOKE/FAST IDLE LEVER
(SIDE VIEW)
WARNING: The chain must not
move when the engine runs at idle speed. If
the chain moves at idle speed refer to CAR-
BURETOR ADJUSTMENT within this
manual. Avoid contact with the muffler. A hot
muffler can cause serious burns.
Choke/
fast idle lever
OFF HALF FULL
6. Pull the starter rope sharply with your
right hand until the engine starts.
7. Allow the engine to run for approximately
30 seconds. Then, squeeze and release
throttle trigger to allow engine to return to
idle speed.
To stop the engine, move the ON/STOP
switch to the STOP position.
To start the engine, hold the saw firmly on
the ground as illustrated below. Make sure
the chain is free to turn without contacting
any object.
STARTING A WARM ENGINE
1. Move ON/STOP switch to the ON position.
2. Slowly press the primer bulb 6 times.
3. Pull the choke/fast idle lever out to the
HALF CHOKE position.
4. Pull the starter rope sharply with your
right hand until the engine starts.
Use only 40 --- 45 cm of rope per pull.
Hold saw firmly while pulling starter rope.
5. Squeeze and release throttle trigger to
allow engine to return to idle speed.
DIFFICULT STARTING (or starting a
flooded engine)
The engine may be flooded with too much
fuel if it has not started after 10 pulls.
Flooded engines can be cleared of excess
fuel by pushing the choke/fast idle lever in
9
Disengaged
completely (to the OFF CHOKE position)
and then following the warm engine starting
procedure listed above. Ensure the ON/
STOP switch is in the ON position. Starting
could require pulling the starter rope handle
many times depending on how badly the unit
is flooded. If engine fails to start, refer to the
TROUBLESHOOTING TABLE.
Braking function control
CHAIN BRAKE
CAUTION: The chain brake must be
checked several times daily. The engine
must be running when performing this proce-
dure. This is the only instance when the saw
should be placed on the ground with the en-
gine running.
WARNING: If the brake band is worn
too thin it may break when the chain brake is
triggered. With a broken brake band, the chain
brake will not stop the chain. The chain brake
should be replaced by an authorized service
dealer if any part is worn to less than 0,5 mm
thick. Repairs on a chain brake should be
made by an authorized service dealer. Take
your unit to the place of purchase if purchased
from a servicing dealer, or to the nearest autho-
rized master service dealer.
S This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
S The inertia activated chain brake is activated
if the front hand guard is pushed forward, ei-
ther manually or by centrifugal force.
Place the saw on firm ground. Grip the rear
handlewith your right hand andthe front han-
dle with your left hand. Apply full throttle by
fully depressing the throttle trigger. Activate
the chain brake by turning your left wrist
against the hand guard without releasing
your grip around the front handle. The chain
should stop immediately.
Inertia activating function control
WARNING: When performing the fol-
lowing procedure, the engine must be turned
off.
S If the brake is already activated, it is disen-
gaged by pulling the front hand guard back
toward the front handle as far as possible.
S When cutting with the saw, the chain brake
must be disengaged.
Grip the rear handle with your right hand and
the front handle with your left hand. Hold the
chain saw approximately 35 cm above a
stump or other wooden surface. Release
your grip on the front handle and use the
weight of the saw to let the top of the guide
bar fall forward and contact the stump.
When the tip of the bar hits the stump, the
brake should activate.
CUTTING METHODS
S
Release the throttle trigger as soon as
the cut is completed, allowing the en-
gine to idle. If you run the saw at full
throttle without a cutting load, unneces-
sary wear can occur.
Toavoid losing control when cut is com-
plete, do not put pressure onsaw at end
of cut.
IMPORTANT POINTS
S Check chain tension before first use and af-
ter 1 minute of operation. See CHAIN TEN-
SION in the ASSEMBLY section.
S Cut wood only. Do not cut metal, plastics,
masonry, non-wood building materials, etc.
S The bumper spike may be used as a pivot
when making a cut.
S Stop the saw if the chain strikes a foreign ob-
ject. Inspect the saw and repair parts as nec-
essary.
S
S Stop the engine before setting the saw down.
TREE FELLING TECHNIQUES
S Keep the chain out of dirt and sand. Evena
small amount of dirt will quickly dull a chain
and increase the possibility of kickback.
S Practice cutting a few small logs using the
following techniques to get the “feel” of us-
ing your saw before you begin a major
sawing operation.
WARNING: Felling a tree requires
chain saw skills and experience. Inexperi-
enced users should not fell trees. Do not at-
tempt any task that makes you feel uncom-
fortable or unsure.
WARNING: Do not cut near buildings
or electrical wires if you do not know the di-
rection of tree fall, at night since you will not
be able to see well, or during bad weather
such as rain, snow, or strong winds. as fall is
unpredictable.
Carefully plan your sawing operation in ad-
vance. You need a clear area all around the
tree so you can have secure footing. Check
for broken or dead branches which can fall
on you causing serious injury.
S
S
S
S
Squeeze the throttle trigger and allow the
engine to reach full speed before cutting.
Begin cutting with the saw frame
against the log.
Keep the engine at full speed the entire
time you are cutting.
Allow the chain to cut for you. Exert only
light downward pressure.
10
Natural conditions that can cause a tree to
fall in a particular direction include:
Hinge holds tree on stump and helps
control fall
Opening
S The wind direction and speed.
of felling
cut
S The lean of the tree. The lean of a tree
might not be apparent due to uneven or
sloping terrain. Use a plumb or level to de-
termine the direction of tree lean.
Closing
of notch
S Weight and branches on one side.
S Surrounding trees and obstacles.
Look for decay and rot. If the trunk is rotted,
it can snap and fall toward the operator.
Make sure there is enough room for the tree to
fall. Maintain a distance of 2-1/2 tree lengths
from the nearest person or other objects. En-
gine noise can drown out a warning call.
Remove dirt, stones, loose bark, nails, sta-
ples, and wire from the tree where cuts are to
be made.
NOTE: Before felling cut is complete, use
wedges to open the cut when necessary to
controlthedirectionof fall. To avoid kickback
or chain damage, use wood or plastic
wedges, but never steel or iron wedges.
S Be alert to signs that the tree is ready to fall:
cracking sounds, widening of the felling cut,
or movement in the upper branches.
S As tree starts to fall, stop saw, put it down,
and get away quickly on your planned re-
treat path.
Plan a clear retreat path
S DO NOT cut down a partially fallen tree with
your saw. Be extremely cautious with par-
tially fallen trees that may be poorly sup-
ported. When a tree doesn’t fall completely,
set the saw aside and pull down the tree with
a cable winch, block and tackle, or tractor.
Direction of Fall
45_
CUTTING A FALLEN TREE
(BUCKING)
Bucking is the term used for cutting a fallen
tree to the desired log length.
FELLING LARGE TREES
(15 cm in diameter or larger)
The notch method is used to fell large trees.
A notch is cut on the side of the tree in thede-
sired direction of fall. After a felling cut is
made on the opposite side of tree, the tree
will tend to fall into the notch.
WARNING: Do not stand on the log
being cut. Any portion can roll causing loss of
footing and control. Do not stand downhill of
the log being cut.
Important points
NOTCH CUT AND FELLING THE
S Cut only one log at a time.
TREE
S Cut shattered wood very carefully; sharp
pieces of woodcould beflung towardoper-
ator.
S Use a sawhorse to cut small logs. Never
allow another person to hold the log while
cutting and never hold the log with your leg
or foot.
S Make notch cut by cutting the top of the
notch first. Cut through 1/3 of the diameter
of the tree. Next complete the notch by cut-
ting the bottom of the notch. See illustra-
tion. Once the notch is cut remove the
notch of wood from the tree.
S Do not cut in an area where logs, limbs,
and roots are tangled. Drag the logs into a
clear area before cutting by pulling out ex-
posed and cleared logs first.
Final cut here. 5 cm above
center of notch.
First cut
Notch
5 cm
TYPES OF CUTTING USED FOR
BUCKING
5 cm
WARNING: If saw becomes pinched
or hung in a log, don’t try to force it out. You
can lose control of the saw resulting in injury
and/or damage to the saw. Stop the saw,
drive a wedge of plastic or wood into the cut
until the saw can be removed easily. Restart
the saw and carefully reenter the cut. Do not
attempt torestart your saw whenit is pinched
or hung in a log.
Second cut
S After removing the wood from the notch,
make the felling cut on the opposite side of
the notch. This is done by making a cut about
two inches higher than the center of the
notch. This will leave enough uncut wood
between the felling cut and the notch to form
a hinge. This hinge will help prevent the tree
from falling in the wrong direction.
Turn saw OFF and use a plastic or
wooden wedge to force cut open.
11
Overcutting begins on the top sideof thelog
with the saw against the log. When overcut-
ting use light downward pressure.
Using a support stand
nd
2
Cut
Overcutting
Undercutting
st
1
Cut
Cut
Cut
Undercutting involves cutting on the under-
side of the log with top of saw against the log.
When undercutting use light upward pres-
sure. Hold saw firmly and maintain control.
The saw will tend to push back toward you.
st
1
nd
2
WARNING: Never turn saw upside
down to undercut. The saw cannot be con-
trolled in this position.
First cut on pressure side of log
LIMBING AND PRUNING
WARNING: Be alert for and guard
against kickback. Do not allow the moving
chain to contact any other branched or objects
at the nose of the guide bar when limbing or
pruning. Allowing such contact can result in
serious injury.
Second cut
Second cut
WARNING: Never climb into a tree to
limb or prune. Do not stand on ladders, plat-
forms, a log, or in any position which can cause
you to lose your balance or control of the saw.
First cut on pressure side of log
BUCKING WITHOUT A
IMPORTANT POINTS
SUPPORT
S Watch out for springpoles. Use extreme
caution when cutting small size limbs. Slen-
der material may catch the saw chain and be
whipped toward you or pull you off balance.
S Be alert for springback. Watch out for
branches that are bent or under pressure.
Avoid being struck by the branch or the saw
when the tension in the wood fibers is re-
leased.
S Overcut through 1/3 of the diameter of the
log.
S Roll the log over and finish with a second
overcut.
S Give special attention to logs under strain
to prevent the saw from pinching. Make
the first cut on the pressure side to relieve
the stress on the log.
S Keep a clear work area. Frequently clear
branches out of the way to avoid tripping
over them.
BUCKING USING A LOG OR
SUPPORT STAND
S Remember your first cut is always on the
pressure side of the log.
LIMBING
S Always limb atreeafter it is cut down. Only
then can limbing be done safely and prop-
erly.
S Your first cut should extend 1/3 of the
diameter of the log.
S Finish with your second cut.
S Leave the larger limbs underneath the
felled tree to support the tree as you work.
S Start at base of the felled tree and work to-
ward the top, cutting branches and limbs.
Remove small limbs with one cut.
S Keep the tree between you and the chain
as much as possible.
Using a log for support
nd
2
Cut
S Remove larger, supporting branches with
the cuttingtechniques described in BUCK-
ING WITHOUT A SUPPORT.
S Always use an overcut to cut small and
freely hanging limbs. Undercutting could
cause limbs to fall and pinch saw.
st
1
Cut
st
1
Cut
PRUNING
WARNING: Limit pruning to limbs
shoulder height or below. Do not cut if
branches are higher than your shoulder. Get
a professional to do the job.
nd
2
Cut
12
S Make your fist cut 1/3 of the way through
the bottom of the limb.
S Next make a 2nd cut all the way through
the limb. Then cut a third overcut leaving
a1 to 2inchcollar fromthetrunk of thetree.
Second cut
Third cut
Collar
First cut
Pruning technique
SERVICE AND ADJUSTMENTS
Cylinder Cover
Screws
WARNING: Improper maintenance
Air Filter
could result in serious engine damage or in se-
rious injury.
WARNING: Disconnect the spark
plug before performing maintenance, except
for carburetor adjustments.
We recommend all service and adjustments
not listed in this manual be performed by an
Authorized Service Dealer.
MAINTENANCE SCHEDULE
Cylinder
Cover
Check:
Fuel mixture level . . . . Before each use
Bar lubrication . . . . . . . Before each use
Chain tension . . . . . . . Before each use
Chain sharpness . . . . Before each use
For damaged parts . . Before each use
For loose caps . . . . . . Before each use
For loose fasteners . . . Before each use
For loose parts . . . . . . Before each use
Inspect and Clean:
BAR MAINTENANCE
If your saw cuts to one side, has to be forced
through the cut, or been run with an improper
amount of bar lubrication it may be neces-
sary to serviceyour bar. A worn bar will dam-
age your chain and make cutting difficult.
After each use, ensure ON/STOP switch is
in the STOP position, then clean all sawdust
from the guide bar and sprocket hole.
To maintain guide bar:
Bar . . . . . . . . . . . . . . . . Before each use
Complete saw . . . . . . . After each use
Air filter . . . . . . . . . . . . . Every 5 hours*
Chain brake . . . . . . . . Every 5 hours*
Spark arresting screen
S Move ON/STOP switch to the STOP posi-
tion.
S Loosen and remove chain brake nuts and
chain brake. Remove bar and chain from
saw.
S Clean the oil holes and bar groove after each
5 hours of operation.
and muffler . . . . . . . . . Every 25 hours*
Replace spark plug . Yearly
Replace fuel filter . . . Yearly
* Hours of Operation
AIR FILTER
Remove Sawdust From
Guide Bar Groove
CAUTION: Do not clean filter in gaso-
line or other flammable solvent to avoid
creating a fire hazard or producing harmful
evaporative emissions.
Cleaning the air filter:
Oil Hole
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
S Burring of guide bar rails is a normal
process of rail wear. Remove these burrs
with a flat file.
S When rail top is uneven, use a flat file to re-
store square edges and sides.
1. Clean the cover and the area around it to
keep dirt and sawdust from falling into
the carburetor chamber when the cover
is removed.
File Rail Edges
and Sides
Square
2. Remove the parts as illustrated below.
3. Wash the filter in soap and water. Rinse
in clean cool water. Air dry completely
before reinstalling.
Worn Groove
Correct Groove
4. Reinstall parts.
13
Replace guide bar when the groove is worn,
the guide bar is bent or cracked, or when
excess heating or burring of the rails occurs.
If replacement is necessary, use only the guide
bar specified for your saw in the repair parts list
or on the decal located on the chain saw.
Idle Speed---T
Allow engine to idle. If the chain moves, idle
is too fast. If the enginestalls, idle is tooslow.
Adjust speed until engine runs without chain
movement (idle too fast) or stalling (idle too
slow). The idle speed screw is located in the
area above the primer bulb and is labeled T.
S Turn idle speed screw (T) clockwise to in-
crease engine speed.
SPARK PLUG
The spark plug should be replaced each
year to ensure the engine starts easier and
runs better. Ignition timing is fixed and non-
adjustable.
S Turn idle speed screw (T) counterclock-
wise to decrease engine speed.
1. Loosen 3 screws on cylinder cover.
2. Remove the cylinder cover.
3. Pull off the spark plug boot.
4. Remove spark plug from cylinder and
discard.
5. Replace with Champion RCJ--7Y spark
plug and tighten securely with a 19 mm
socket wrench. Spark plug gap should be
0,5 mm.
STORAGE
WARNING: Stop engine and allow to
cool, and secure the unit before storing or
transporting in a vehicle. Store unit and fuel
in an area where fuel vapors cannot reach
sparks or open flames from water heaters,
electric motors or switches, furnaces, etc.
Store unit withall guards in place. Position so
that any sharp object cannot accidentally
cause injury to passersby. Store the unit out
of reach of children.
6. Reinstall the spark plug boot.
7. Reinstall the cylinder cover and
screws. Tighten securely.
Cylinder Cover
3
S Before storing, drain all fuel from the unit.
Start engine and allow to run until it stops.
S Clean the unit before storing. Pay particu-
lar attention to the air intake area, keeping
it free of debris. Use a mild detergent and
sponge to clean the plastic surfaces.
S Donot store theunit or fuel in a closedarea
where fuel vapors can reach sparks or an
openflame from hot water heaters, electric
motors or switches, furnaces, etc.
Screws
Spark
Plug
Cylinder
Cover
S Store in a dry area out of the reach of chil-
dren.
S Ensure the machine is cleaned and that a
complete service is carried out before
long--term storage.
Spark Plug Boot
S The guide bar and chain must always be
covered with a scabbard when the machine
is being transported or in storage in order to
prevent accident contact with the sharp
chain. Even a non--moving chain can cause
serious cuts to yourself or persons you
bump into with an exposed chain.
CHAIN SHARPENING
Chain sharpening is a complicated task that
requires special tools. We recommend that
you refer chain sharpening to a professional
chain sharpener.
CARBURETOR ADJUSTMENTS
WARNING: The chain will be moving
during most of this procedure. Wear your pro-
tective equipment and observe all safety pre-
cautions. The chain must not move at idle
speed.
The carburetor has been carefully set at the
factory. Adjustments may be necessary if
you notice any of the following conditions:
S Chain moves at idle. See IDLE SPEED--T
adjusting procedure.
S Saw will not idle. See IDLE SPEED--T ad-
justing procedure.
CAUTION: It is important to prevent
gum deposits from forming in essential fuel
system parts such as the carburetor, fuel fil-
ter, fuel hose, or fuel tank during storage. Al-
cohol blended fuels (called gasohol or using
ethanol or methanol) can attract moisture
which leads to fuel mixture separation and
formation of acids during storage. Acidic gas
can damage the engine.
14
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing all of
the recommended remedies below except remedies that require operation of the unit.
TROUBLE
CAUSE
REMEDY
Engine will not
start or will run
only a few
seconds after
starting.
1. Move ignition switch to ON.
2. See “Difficult Starting” in
Operation Section.
3. Fill tank with correct fuel mixture.
4. Install new spark plug.
5. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
1. Ignition switch off.
2. Engine flooded.
3. Fuel tank empty.
4. Spark plug not firing.
5. Fuel not reaching
carburetor.
1. Idle speed requires
adjustment.
2. Carburetor requires
adjustment.
Engine will
not idle
properly.
1. See “Carburetor Adjustment” in the
Service and Adjustments Section.
2. Contact an authorized service dealer.
1. Clean or replace air filter.
2. Clean or replace plug and regap.
3. Disengage chain brake.
Engine will not
accelerate,
lacks power,
or dies under
a load.
1. Air filter dirty.
2. Spark plug fouled.
3. Chain brake engaged.
4. Carburetor requires
adjustment.
4. Contact an authorized service dealer.
Engine
smokes
1. Too much oil mixed with
gasoline.
1. Empty fuel tank and refill with
correct fuel mixture.
excessively.
1. Idle speed requires
adjustment.
2. Clutch requires repair.
1. See “Carburetor Adjustment” in the
Service and Adjustments Section.
2. Contact an authorized service dealer.
Chain moves
at idle speed.
DECLARATION OF CONFORMITY
EC Declaration of Conformity (Only applies to Europe)
We, Husqvarna Outdoor Products Italia, S.p.A., Valmadrera, Italy. Tel:
+39--0341--203211, declare that the chain saw models McCulloch M3816 and M4218
CSI---AV from serial numbers 2008--040(N or D) 00001 and onwards (the year is clearly
stated on the rating plate, followed by the serial number), comply with the requirements
of the COUNCIL’S DIRECTIVES:
of 22 June 1998 “relating to machinery” 98/37/EC, annex IIA;
of 3 May 1989 “relating to electromagnetic compatibility” 89/336/EEC, and applicable
supplements; and
of 8 May 2000 “relating to the noise emissions in the environment” in accordance with
Annex V of 2000/14/EC. The measured sound power is 108 dB(A), the guaranteed
sound power is 118 dB(A) and the net power is 1,6 kW or 1,7 kW.
The following standards have been applied: ISO 11681 -1:2004, EN/ISO 12100-1:2003,
EN/ISO 12100-2:2003, and CISPR 12:2001.
Notified body, 0404 the Swedish Machinery Testing Institute, Fyrisborgsgatan 3
S--754 50 Uppsala, Sweden, has carried out EC type approval. The certificate(s) is
numbered: 404/02/901.
The supplied Chain Saw conforms with the sample that underwent the EC typeapproval.
08--02--09
Michael S. Bounds, Director
Product Safety and Standards
Handheld Consumer Products
15
TECHNICAL DATA SHEET
Engine
Cylinder volume, cm
Stroke, mm
Idle speed, rpm
Recommended max.
speed, unloaded, rpm
Power, kW
M3816
38
32
M4218
42
32
Noise levels
M3816
M4218
3
Equivalent (see note 1)
noise pressure level at
operator’s ear, measured
according to relevant
international standards,
dB(A)
3,000
3,000
13,000
1,6
13,000
1,7
97
97
Equivalent (see note 1)
noise power level,
measured according to
relevant international
standards, dB(A)
Ignition system
Manufacturer
Type of ignition system CD
Spark plug
Walbro
Champion
0,5
106
106
Electrode gap, mm
Vibration levels
(see note 2)
Fuel and lubrication system
2
Manufacturer
Walbro
WT--662
0,38
Front handle, m/s
Rear handle, m/s
5,5
8,5
5,5
8,5
2
Carburetor type
Fuel capacity, litre
Oil pump capacity at
8500 rpm, ml/min
Oil capacity, litre
Type of oil pump
Chain/bar
4 -- 8
0,2
Automatic
Standard bar length, in/cm
Recommended bar lengths,
in/cm
16/40 18/45
16/40 18/45
Usable cutting length, in/cm 15,5/39 17,5/44
Chain speed at maximum
Weight
Without bar and chain, kg 4,8
power, m/sec
Pitch, inches
19
19
0,375 0,375
BAR
Pitch
Inches Tip Radius
0,375
0,375
0,375
0,375
CHAIN
Max
Thickness of drive link, mm 1,3
1,3
6
Length
Inches
16
18
16
No. of teeth on drive sprocket
6
Note 1: Equivalent noise level is, according to
ISO 22868, calculated as the time--weighted en-
ergy total for noise levels under various working
conditions with the following time distribution,
1/3 idle, 1/3 full load, 1/3 full speed.
7T Oregon 91VJ
7T Oregon 91VJ
7T Oregon 91VG
7T Oregon 91VG
18
Note 2: Equivalent vibration level is, according
to ISO 22867, calculated as the time--weighted
energy total for vibration levels under various
working conditions with the following time dis-
tribution: 1/3 idle, 1/3 full load, 1/3 full speed.
Inch/mm : dl
16/40 : 56
18/45 : 62
91VJ
0,375
0,050/1,3 5/32 / 4,0
0,025/0,65
16/40 : 56
18/45 : 62
85°
30°
0°
91VG
ADDRESS: Husqvarna Outdoor Products Italia S.p.A.
Via Como 72
Valmadrera, Lecco
ITALY I--23868
16
STATEMENT OF WARRANTY
Husqvarna Outdoor Products provides war-
Nothing contained in this warranty is in-
tended to purport to restrict, modify or ex-
clude the operation of any legislation in the
State where the product was purchased.
The following items are not covered by this
warranty:
ranty to the initial purchaser for all products
that are sold by an authorised Husqvarna
Outdoor Products Dealer.
The warranty provides the purchaser with a
guarantee against faulty workmanship in
manufacture and/or defective components.
If any product supplied by Husqvarna Out-
door Products is found to be defective due to
faulty manufacture within the warranty peri-
od, Husqvarna Outdoor Products through its
Authorised Servicing Dealers will effect the
repair or replacement at their discretion to
the customer, free of charge providing;
S The fault is reported directly to the Autho-
rised Servicing Dealer.
S Normal customer maintenance items
which become worn through normal regu-
lar use, including, but not limited to, belts,
blades, blade adapters, globes, filters,
guide bars, lubricants, rewind springs,
saw chain, spark plugs, starter ropes, and
tines;
S Natural discolouration of material due to
ultraviolet light;
S Engine and drive systems not manufac-
tured by Husqvarna Outdoor Products,
these items are covered by the respective
original equipment manufacturers warran-
ty, all claims must be sent to the appropri-
ate manufacturer.
S Proof of purchase is provided.
S The fault is not caused by misuse, neglect
or faulty adjustment by the user.
S The failure has not occurred through nor-
mal wear and tear.
S The product has not been serviced, re-
paired or alterations made by any person
not authorised by Husqvarna Outdoor
Products.
S The machine has not been used for hire.
Product Warranty Period
Domestic
12 Months
12 Months
12 Months
12 Months
12 Months
12 Months
Commercial
90 Days
90 Days
90 Days
90 Days
90 Days
90 Days
Non--Powered Push Mowers
Electric and Petrol Walk--Behind Mowers
Electric and Petrol Chainsaws
Electric and Petrol Trimmers
Electric and Petrol Blowers
Petrol Ride--on Mowers
17
|