Metra Electronics Automobile Accessories 95 7510 User Manual

INSTALLATION INSTRUCTIONS FOR PART 95-7510  
APPLICATIONS  
Mazda RX-8  
2004-2008  
95-7510/  
95-7510HG  
KIT FEATURES  
• Double DIN Radio Provision  
• Stacked ISO Mount Units Provision  
• TWO FINISHES AVAILABLE:  
99-7510=BLACK, 99-7510HG=GLOSS BLACK  
KIT COMPONENTS  
• A) Radio / Climate Control Housing • B) Double DIN Radio Brackets • C) Rear Support  
• D) Interface • E) Wiring Harnesses • F) (2) Climate Control Extension Harnesses  
D
C
B
A
F
E
TOOLS REQUIRED:  
Small Flat Blade Screwdriver/ Panel Removal Tool  
• Phillips Screwdriver • Socket Set • Cutting Tool  
1-800-221-0932  
© COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION  
 
95-7510 DASH DISASSEMBLY  
MAZDA RX-8 2004-2008  
A
Disconnect the negative battery ter-  
1
minal to prevent an accidental short  
circuit.  
2
3
4
Unscrew the shift knob counter clock-  
wise to remove. (Figure A)  
Unclip and remove the shifter trim  
panel. (Figure B)  
Remove (2) Phillips screws from the  
bottom of the ashtray assembly then  
unclip and remove the assembly.  
B
(Figure C)  
5
Unclip and remove the knee panel on  
the driver’s side under the steering  
column (Figure D) then remove (1) 10  
MM bolt from the side of the radio  
bracket. (Figure E)  
Continued on page 2.  
C
D
AC  
FM1 877  
1
 
95-7510 DASH DISASSEMBLY  
MAZDA RX-8 2004-2008  
E
Remove (2) Phillips screws from the  
bottom of the radio/climate control  
panel. (Figure F)  
6
7
8
AC  
FM1 877  
Unsnap radio/climate control panel  
including radio chassis. Unplug and  
remove panel and chassis. (Figure G)  
Remove (3) Phillips screws securing  
the factory display harness to the  
radio chassis. Unplug and remove  
display harness. (Retain display har-  
ness for re-use during kit assembly.)  
(Figure H)  
F
9
Remove (4) screws securing the radio  
chassis to the radio/climate control  
panel. (Figure I)  
10 Remove (6) screws securing the cli-  
mate controls from the radio/climate  
control panel. Unplug and remove the  
climate controls. (Retain the screws  
and climate controls for re-use during  
kit assembly.) (Figure J)  
Continued on page 3.  
G
H
AC  
FM1 877  
2
 
95-7510 DASH DISASSEMBLY  
MAZDA RX-8 2004-2008  
I
Remove (17) screws securing the cir-  
11  
cuit board to the radio/climate control  
panel to access the plug for the haz-  
ard switch assembly. (Figure K)  
12 Remove (2) screws securing the haz-  
ard switch to the radio/climate control  
panel. Unplug and remove hazard  
switch. (Retain the screws and hazard  
switch for re-use during kit assem-  
bly.) (Figure L)  
REMOVE (2) SCREWS PER SIDE  
Continue to kit assembly.  
J
L
K
3
 
95-7510 KIT ASSEMBLY  
DOUBLE DIN RADIO PROVISION OR  
STACKED ISO MOUNT UNITS PROVISION  
*Note: Refer also to the instructions included with the aftermarket radio.  
A
Cut the top (2) mounting locations off  
of the climate controls to provide  
clearance for the aftermarket radio.  
(Figure A)  
1
2
3
4
5
Secure the climate control to the  
radio/climate control housing using (4)  
of the factory screws removed in step  
(10) of the dash disassembly. (Figure B)  
Secure the hazard switch assembly to  
the radio/climate control housing using  
the factory screws removed in step  
(12). (Figure B)  
B
Attach the Double DIN brackets to the  
Double DIN or stacked ISO Mount  
unit(s) using the hardware supplied  
with the unit(s). (Figure C)  
1
0
2
Attach the rear support to the unit(s)  
using the hardware supplied with the  
unit(s). (Figure D)  
3
4
Continue to final assembly.  
C
D
4
 
95-7510 FINAL ASSEMBLY  
FINAL ASSEMBLY  
A
B
(A) Strip wire ends back 1/2"  
B) Twist ends together  
C) Solder  
C
D
D) Tape  
Locate the factory wiring harness in the dash. Use the supplied wire harnesses and  
make the connections as shown. (Isolate and individually tape off the ends of any  
unused wires to prevent electrical short circuit). Refer to Metra/EIA Wiring Code  
below.  
1
FINAL WIRING CONNECTIONS  
Make wiring connections using the EIA color code chart shown below and the  
instructions included with the head unit. Metra recommends making connections as  
shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any  
unused wires to prevent electrical short circuit.  
METRA / EIA WIRING CODE  
12V Ignition / Acc. . . . . . Red  
Right Front (+) . . . . . . . . Gray  
12V Batt / Memory. . . . . Yellow  
Ground . . . . . . . . . . . . . . Black*  
Power Antenna. . . . . . . . Blue  
Right Front (-). . . . . . . . . Gray/ Black  
Left Front (+) . . . . . . . . . White  
Left Front (-). . . . . . . . . . White / Black  
Right Rear (+). . . . . . . . . Violet  
Amp Turn-On . . . . . . . . . Blue / White  
Amp Ground . . . . . . . . . . Black / White  
Illumination . . . . . . . . . . Orange  
Dimmer . . . . . . . . . . . . . . Orange / White  
Right Rear (-) . . . . . . . . . Violet / Black  
Left Rear (+). . . . . . . . . . Green  
Left Rear (-) . . . . . . . . . . Green / Black  
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.  
All colors may not be present on all leads due to manufacturer’s specifications.  
Continued on Page 6  
5
 
95-7510 FINAL ASSEMBLY  
Continued from Page 5  
WARNING!  
FAILURE TO INSERT THE HVAC CABLES INTO THE CORRECT  
LOCATION WILL CAUSE DAMAGE TO THE INTERFACE AND MAKE  
THE DISPLAY AND HVAC CONTROLS NOT FUNCTION PROPERLY  
Attach the (2) climate control extension harnesses to the temperature control  
cable and the fan control cable on the factory climate control.  
2
3
Plug the Temperature Control cable from the factory climate control into the port  
on the interface that reads “TEMP”.  
Plug the Fan Control cable from the factory climate control into the port on the  
interface that reads “FAN”.  
4
5
Plug the Display cable removed in step 8 of the dash disassembly into the port  
on the interface that reads “DISP”.  
6
Plug the Hazard Switch extension cable into the end of the hazard switch and  
the other end of the extension cable into the port next to the “DISP” port.  
Continued on Page 7  
6
 
95-7510 FINAL ASSEMBLY  
Continued from Page 6  
A
OBDII CONNECTOR FACE VIEW  
PINK WIRE  
1 2 3 4 5 6 7 8  
9 10 11 12 13 14 15 16  
PINK/BLUE WIRE  
When using the Nav features of the interface you will need to connect the 2 pin  
harness and run the 2 wires to the OBDII connector and connect them in the  
position shown. (Figure A)  
7
8
The following wires on the 10 pin harness are for the aftermarket radios that have navigation built in:  
A. Connect the green wire to the parking brake wire of the aftermarket navigation radio.  
B. Connect the pink /blue wire to the VSS or speed sense wire of the aftermarket navigation radio.  
C. Connect the green/purple wire to the reverse wire of the aftermarket navigation radio.  
NOTE: Reverse output is NOT present on manual transmission vehicles.  
Re-connect the negative battery terminal and test the unit for proper operation.  
Reassemble radio and dash assemblies in reverse order of disassembly.  
9
10  
7
 
95-7510 KIT ASSEMBLY  
DISPLAY CUSTOMIZATION  
*Note: Refer also to the instructions included with the aftermarket radio.  
1
2
0
3
A/C  
OPEN  
TILT  
4
AC  
MODE  
FM1 877  
1
2
Press and hold the A/C Mode button to scroll through the various kit options (AMB  
TEMP ON or OFF, AMB TEMP C or F, SET TIME 12/24H, and SET TEXT).  
When you see the option you want just let the button go and the action on the  
screen will be performed. (ie: To turn the ambient temperature on you would scroll  
through until the display says “AMB TEMP ON” and let the button go.)  
3
4
5
To set the time hold down the A/C Mode button until the display says “SET TIME  
12/24H” then let the button go.  
To switch between 12H and 24H press the front defrost button to the left of the  
A/C Mode button.  
To change the Hour press the rear defrost button to the right of the A/C Mode  
button.  
6
7
To change the minute press the A/C button at the top of the A/C Mode button.  
At any time if you do not press any buttons for 5 seconds the display will save and  
return to the default screen and the climate control buttons will return to their  
normal configuration.  
8
9
If you hold the A/C Mode button down long enough the display will say “SET  
TEXT”. This will allow you customize the default text on the display.  
Once the display says “SET TEXT” let go and the first letter of the display will begin  
blinking.  
10 Press the front defrost button to move the cursor left and the rear defrost button  
to move the cursor to the right.  
11 You can scroll up with the A/C button and down with the Recirc/Fresh button  
through the various alpha, numeric, and symbol characters.  
12 When you are finished entering your text if you do not press any buttons for 5 sec-  
onds the display will save and return to the default screen and the climate control  
buttons will return to their normal configuration.  
8
 
95-7510  
NOTES  
9
 
95-7510 INSTRUCTIONS  
1-800-221-0932  
REV. 10/30/08 © COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION INST95-7510  
 

Lasko Electric Heater 675945 User Manual
LG Electronics Car Satellite TV System 42LP870H User Manual
LG Electronics Microwave Oven LRM1230W User Manual
Link electronic Portable Generator IEC 833 User Manual
Loewe DVD Player ViewVision DR+ User Manual
LOREX Technology Security Camera SG14S1022P User Manual
Makita Saw LS1040 User Manual
Manhattan Computer Products TV Receiver HDS2 User Manual
Marshall electronic Car Video System V R154P User Manual
McCulloch Lawn Mower M53 140WF User Manual